valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
When the air is cool with low humidity, “sweating” may not be evident. • How long has the heater been operating? During initial pool heating in cold weather, it may require a week to elevate the pool temperature to a comfortable level. Normally, it takes about 4 days. • How many hours per day is the unit operating? Remember that the heat pump only operates while the pool pump is running. Set the time clock to permit 24 hour per day 7 operation. After the desired temperature is reached, return the system to normal operation of 8-10 hours per day. • Is airflow through the unit being obstructed? Restrictions such as shrubbery, tall grass, dirty coils, or any other obstruction to airflow will reduce performance. • Is the pool blanket/cover being used? Unblanketed pools can lose up to 10 degrees per night compared to 4 degrees or fewer when a blanket is used. Without a blanket, the total heat gained during the day can be lost overnight. • Are rapid heat losses occurring in some other way, such as high wind, waterfalls, spa spillage, bubblers, rainfall, flow through solar panels at nights, or a high water table? • Is water flow through the unit adequate? Check the system for obstructions, such as a clogged filter pump strainer or a dirty filter. B. UNIT IS NOT RUNNING • Is the control panel Power lamp ON? If not, the circuit breaker may be shut OFF or tripped. Reset the breaker by switching it OFF, then back ON. Verify that the breaker is set and operating properly before calling for service. • Is the thermostat setting correct? Verify that the temperature has been properly set on the thermostat, and that it is higher than the current water temperature. • Have you waited 6 minutes for the time delay? After the unit has been running and then shut OFF for any reason, there is a 6-minutes timed cycle before operation can begin again. •Is the Water Flow lamp OFF? This lamp will turn OFF if not enough water is flowing through the heater. Improperly positioned valves or a dirty filter could decrease the flow of water required for efficient operation. When the Water Flow lamp is ON, proper flow is present. If this lamp is OFF, but you can feel normal flow at the pool returns, check the water valves or settings. •Is the Defrost Active lamp OFF? If this lamp is ON, the fan will be running but not the compressor. The unit is waiting for the frost to melt or the air temperature to rise before heating is resumed. •Is the Heat Demand lamp ON? If not, then the thermostat setting is not higher than the temperature of the pool water. Raise the thermostat setting. •Is the Low Pressure lamp ON? If this lamp is ON, there is a problem with the unit that will require service. Turn the unit OFF and call the number shown in the CONTACT INFORMATION at the beginning of this manual. SERVICE CALL REQUESTS Determine if the problem is: • Warranty Service (within 5 years of installation) • Non Warranty Service (beyond 5 years of installation) • Maintenance-related (power supply, water flow, or time clock adjustment) NOTE: The MANUFACTURER IS NOT RESPONSIBLE for maintenance adjustments. 8 POWER SUPPLY • Verify that all circuit breakers are reset and working properly. •If the Power lamp on the control panel still does not light, contact the installing dealer, since it may be a power problem requiring an electrician. WATER FLOW • Verify that the filter is clean to provide good flow. • Verify that the valves are properly positioned. •If the Water Flow lamp on the control panel still does not light, and water is circulating in the pool or spa, contact the installing dealer to adjust the valves. TIME CLOCK ADJUSTMENT Verify that the time clock is set to permit the heater to run long enough to heat properly. 9 10 Plumbing Diagrams For systems with pumps of less than 2 HP (under 80 gpm), no external bypass is required. Connections are 2-inch pipe slip. Plumb the heat pump after the filter and before any chlorinators. Water In (from pool or Spa) Water Out (to pool or Spa) Filter For systems with pumps of 2 HP or greater (over 80 gpm), an external bypass is required. Adjust the bypass valve to divert a minimum of 40 gpm through the heat pump. Connections are 2-inch pipe slip. Plumb the heat pump after the filter and before any chlorinators. Water In (from pool or Spa) Water Out (to pool or Spa) Filter 11 Heat Pump Schematic 1 2 3 4 ABCD 4321 DCBA Title Number RevisionSizeADate: 27-Jan-2003 Sheet of File: C:\Pool Fact\Poofact\Poofact.ddb Drawn By: 123456789101112131415161718192021222324TB1Control Panel Interface D4 Delay Active D5 Active D6 Pressure D1 Power D2 Water Flow D3 Heat Demand R1 Spa R2 Pool K1Contactor K2Fan Relay E4 E5 E6 E7E10 E11 E12 E13 PotPotU1Water Temp Thermostat S4Water Flow RT1Optional Water Temp Sensor RT2Water Temp Sensor M1Compressor Motor M2Fan Motor C1 C2T1 F21 Amp 208/230 V 1-Phase 60 Hz208/230 V 1-Phase 60 Hz GND 13 K3Delay Timer +24 V/ Power Lamp Defrost Lamp Compressor Lamp Water Flow Lamp GNDDefrost Compressor Heat Demand L...
Questo manuale è adatto anche per i modelli :Piscine - RHP100 (1.42 mb)
Piscine - RHP115 (1.42 mb)