valutazioni - , GPA:
(
)
)
Produttore : Dolmar
File Size : 3.95 mb
File Nome : 5703b295-011a-44aa-86e9-5da89af497bb.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Reinforcement rods must be cut in the prescribed sequence and in accordance with applicable safety regulations. NOTE: Mortar, stone, and concrete develop large quantities of dust during cutting. To increase the lifetime of the cutting disc (by cooling), to improve visibility, and to avoid excessive dust creation, we strongly recommend wet cutting instead of dry cutting. 19 20 21 10 In wet cutting, the disc is wetted at an equal rate on both sides by a trickle of water. DOLMAR offers the right accessories for all wet cutting applications (see also "SPECIAL ACCESSORIES"). - Remove foreign objects such as sand, stones and nails found within the working area. Caution: Watch out for electric wires and cables! The rapid rotation of the cutting disc at the point of contact throws fragments out of the cut groove at high speed. For your safety, swing the protection hood down as far as possible (23), so that material fragments are thrown forward, away from the operator. - Mark the cut, and then make a groove about 5 mm (just under 1/5") along the entire length of the planned cut. This groove will then guide the Power Cut accurately guring the actual cutoff. NOTE: For long, straight cuts we recommend using a trolley (24, see also "SPECIAL ACCESSORIES"). This makes it much easier to guide the unit straight. - Perform the cut with a steady back-and-forth motion. - When cutting slabs to size, you need not cut through the entire material thickness (creating unnecessary dust). Instead, simply make a shallow groove, and then knock off the excess material cleanly on a flat surface (25). CAREFUL! When cutting into lengths, cutting through material, making cutouts, etc., always make sure to plan the direction and sequence of cuts in such a way that the disc does not get jammed by the cut-off piece, and that no persons can be injured by falling pieces. Transport and storage - Always turn off the Power Cut when transporting it or moving it from place to place on a site (26). - Never carry or move the unit with the engine on or the disc moving! - Carry the unit only by the tubular (middle) handle with the cutting disc pointing behind you (26). Avoid touching the exhaust muffler (burn hazard!) - When moving the Power Cut over longer distances, use a wheelbarrow or wagon. - When transporting the Power Cut in a vehicle, make sure it is securely positioned in such a way that no fuel can leak out. Always remove the cutting disc before transporting the unit in a vehicle. - The Power Cut should be stored safely in a dry place. It must not be left outdoors! Always dismount the cutting disc before storage. Keep the Power Cut away from children. - Before long-term storage and before shipping the Power Cut, follow the instructions in the chapter on "Periodic care and maintenance". ALWAYS empty the fuel tank and run the carburetor dry. - When putting cutting discs in storage, be careful to: - Clean and dry them well. - Store them lying down flat. - Avoid dampness, freezing temperatures, direct sunshine, high temperatures and temperature fluctuations, as these can cause breakage and splintering. - Always check new cutting discs or cutting discs that have been in storage to make sure that they are free of defects and before the first cut test-run the tool at top speed for at least 60 seconds. Keep body parts and people well away out of range of the direction of the cutting disc during this test. 23 26 STOP 25 24 Maintenance Maintenance -Always check the Power Cut before using it to make sure that it is in good working order. In particular, make sure that the cutting disc is properly mounted. Make sure that the cutting wheel is undamaged and suitable for the job it will be used for. -Operate the Power Cut only at a low noise and emission level. For this ensure the carburetor is adjusted correctly. -Clean the Power Cut regularly. -Check the fuel tank cap regularly for good sealing. Observe the accident prevention instructions issued by trade associations and insurance companies. NEVER make any modifications to the Power Cut! You will only be putting your own safety at risk! Perform only the maintenance and repair works described in the instruction manual. All other work must be carried out by DOLMAR Service. Use only original DOLMAR spares and accessories. The use of non-DOLMAR spares, accessories, or cutting discs increases the risk of accident. We cannot accept any responsibility for accidents or damage occurring in association with the use of cutting discs or accessories other than original DOLMAR. First aid For the event of a possible accident, please make sure that a first aid kit is always immediately available close by. Immediately replace any items used from the first aid box. When calling for help, give the following information: -Place of the accident -What happened -Number of injured people -Kind of injuries -Your name! 27 STOP NOTE Individuals with poor circulation who are exposed to excessive vibration may experience injury to blood...