valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
NOTE! When the winter plug is fitted the winter flap must be open. IMPORTANT! If the temperature rises above -5°C (23°F) or 0°C (32°F) respectively the saw MUST be restored to its normal settings. Otherwise there is a risk of overheating, which can cause severe engine damage. IMPORTANT! Any maintenance other than that described in this manual must be carried out by your servicing dealer. 1 2 5 4 3 H H The oil pump is adjustable. Adjustments are made by turning the screw using a screwdriver or combination spanner. The saw is supplied from the factory with the screw set to position 2. Turning the screw clockwise will reduce the oil flow and turning the screw anti-clockwise will increase the oil flow. Adjustment of the oil pump + – 2 1 3 WARNING! The engine must not be running when making adjustments. Recommended settings: Bar 13"-15": Position 1 Bar 15" -18": Position 2 Bar 18"-20": Position 3 Electrically heated carburetor (CS 2159 WH) This chain saw is, if it has model code WH, equipped with electrically heated carburetor. The electrical heating prevents icing in the carburetor. A thermostat regulates heating so that the carburetor always has the correct temperature. English – 33 Below you will find some general maintenance instructions. If you have more questions, contact your servicing dealer. Weekly maintenance 1. Check that the AV elements are not soft or torn. 2. Lubricate the clutch drum bearing. 3. File off burrs, if any, on the sides of the bar. 4. Clean the spark plug and check the gap. The correct gap is 0,5 mm (0,020 inch). 5. Check the starter and the recoil spring. Clean the fins on the flywheel. 6. Clean the cooling fins on the cylinder. 7. Clean or change the screen in the muffler. 8. Clean the carburetor body and air box. Monthly maintenance 1. Check the brake band on the chain brake for wear. 2. Check the clutch centre, clutch drum and clutch spring for wear. 3. Clean the outside of the carburetor. 4. Change the fuel filter. 5. Clean the inside of the fuel tank. 6. Clean the inside of the oil tank. 7. Check all cables and connections. 8. Change the spark plug. 9. Change the air filter. MAINTENANCE Daily maintenance 1. Check the throttle trigger for smooth operation. If any binding occurs, or if engine fails to return to idle, the saw should be taken to your dealer, before it is used again. Also, be sure that the trigger cannot be pulled until the throttle trigger lockout is depressed. 2. Clean the chain brake and check its function according to the instructions. Make sure that the chain catcher is undamaged. Otherwise replace it immediately. 3. Clean or replace the air filter as necessary. Check for damage or holes. 4. The bar should be turned daily for more even wear. Check the lubrication hole in the bar, to be sure it is not clogged. Clean the bar groove, if the bar has a sprocket tip, this should be lubricated. 5. Check the function of the oiler to be sure the bar and chain receive proper lubrication. 6. Sharpen the chain and check its tension and condition. Check the drive sprocket for wear. Replace if necessary. 7. Check the starter and starter cord for wear or damage. Clean the air intake slots on the starter housing. 8. Check for any loose nuts and screws and retighten if necessary. 9. Test the stop switch to be sure it shuts off the engine. 1 3 4 0,5 mm 5 6 7 8 2 3 4 7 8 0,5 mm 1 2 5 6 9 3 6 8 2 9 7 4 1 5 TECHNICAL DATA CS 2159 Engine Cylinder volume, cu.in/cm3 3,60/5,09 Cylinder bore, inch/mm 1,85/47 Stroke, inch/mm 1,34/34 Idle speed, rpm 2 700 Power, kW/ rpm 3,0/ 9 000 Ignition system Manufacture SEM Type of ignition system CD Spark plug NGK BPMR 7A Champion RCJ 7Y Electrode gap, inch/mm 0,02/0,5 Fuel and lubrication system Manufacturer Walbro Carburetor type HDA 199 Fuel capacity, US pint/litre 1,43/0,68 Oil pump capacity at 9000 rpm, ml/ min 6-17 Oil capacity, US pint/litre 0,80/0,38 Type of oil pump Automatic Weight Without bar and chain, Lbs/kg CS 2159: 12,3/5,6 CS 2159 W: 12,6/5,7 CS 2159 WH: 12,6/5,7 CS 2159 C: 12,4/5,6 CS 2159 CW: 12,6/5,7 CS 2159 CWH: 12,6/5,7 Chain/bar Standard bar length, inches/cm 15"/38 Recommended bar lengths, inches/cm 13-20"/33-50 Usable cutting length, inches/cm 12-19"/31-48 Chain speed at max. power, m/sec 20 Pitch, inch/mm 0,325"/8,25 3/8"/9,52 Thickness of drive link, inch/mm 0,050"/1,3 0,058"/1,5 0,063"/1,6 Number of teeth on drive sprocket 7 Recommended original and replacement bar and chain combinations Following is a list of recommended cutting equipment for the Jonsered chain saw model CS 2159. The combinations of powerhead, bar and chain have been investigated in accordance with the kickback and vibration requirements of ANSI B 175.1 – 2000. The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the corresponding maximum nose radius of a solid bar. The following list is the chain saw manufacturers recommendations. There may be other combinations available, which will also achieve kickback re...