valutazioni - 1, GPA: 4 ( )

Produttore : Makita File Size : 9.4 mb File Nome : Lingua di insegnamento:

Heavy-duty, nonslip gloves improve your grip and protect your hands. Good footing is most important in chain saw work. Wear sturdy boots with nonslip soles. Steel-toed safety boots are recommended. Proper eye protection is a must. Non-fogging, vented goggles and a face screen is recommended. Their use reduces the risk of eye and facial injury. Wear an approved safety hard hat to protect your head. Chain saw noise may damage your hearing. Always wear noise protection equipment (ear plugs or ear muffs) to protect your hearing. Continual and regular users should have their hearing checked regularly. Wear protective helmet, eye and ear protection The saw Parts of the chain saw: illustrations and description of parts see page 16. WARNING ! Never modify a chain saw in any way. Only attachments supplied by MAKITA or expressly approved by MAKITA for use with the specific saw are authorized. WARNING ! Bow guide bars substantially increase the potential for kickback and severe or fatal injury due to the greater kickback zone of the bow design. Bow guide bars are not recommended for use on MAKITA chain saws nor are they approved by the ANSI B 175.1-2000 chain saw safety standard. The use of the saw Transporting the chain saw WARNING! Always stop'fhe engine before putting a chain saw down or carrying it. Carrying a chain saw with the en- gine running is extremelydangerous. Accidental acceleration of the engine can cause the chain to rotate. Avoid touching the hot muffler. By hand: When carrying your saw by hand, the engine must be stopped and the saw must be in the proper position. The chain protection cover should be over the chain and the guide bar must point backwards. When carrying your saw the bar should be behind you (fig. 4). By vehicle: When transporting in a vehicle, keep chain and bar covered with the chain guard. Properly secure your saw to prevent turnover, fuel spillage and damage to the saw. Make sure the saw in not exposed to heat or sparks. Chain saw operating instructions For assembly follow the procedure in the appropriate section"Mounting Guide Bar and Chain'lofthis manual. MAKITA chain, guide bar and sprocket must match each other (see the appropriate section in this manual). WARNING! Proper tension of the chain is extremely important. In order to avoid false setting the tensioning procedure must be followed as described in this manual. Always make sure the hexagonal nut(s) for the sprocket guard is (are) tightened securely after tensioning the chain. Check chain tension once more after having tightened the nuts and thereafter at regular intervals (always before starting to work). If the chain becomes loose while cutting, shut off the engine and then tighten. Never try to tighten the chain while the engine is running! Fueling Your MAKITA saw uses on oil-gasoline mixture for fuel (see chapter "Fuel" of this manzal). 5 WARN IN G! Gasoline is an extremely flammable fuel. Use extreme caution when handling gasoline or fuel mix. Do not smoke or bring any sparks or flame near the fuel (fig. 5). Fueling instructions @ Fuel your chain saw in well ventilated areas or out- doors. Always shut off the engine and allow it to cool before refueling. Select bare ground for fueling and move the chain saw at least 10feet (3 m) from fueling spot before starting the engine (fig. 5a). Wipe off any spilled fuel before starting your saw and check for leakage. Check for fuel leakage while refueling and during operation. If fuel or oil leakage is found, do not start or run the engine until leak is fixed and spilled fuel has been wiped away. Clothing with fuel on it has to be changed immediately (this is a danger to your life!). Avoid skin contact with fuel. Never loosen or remove the cap of the fuel tank while the engine is running. Starting Do not drop start. This method is very dangerous be- cause you may lose control of the saw (fig. 6). I f Place the chain saw on firm ground or other solid surface in an open area. Maintain a good balance and secure footing. Place your right foot through the rear handle opening and firmly grasp the front handle with your left hand (fig. 6a). Be absolutely sure that guide bar and chain are clear of you or all other obstructions and objects, including the ground, because when the engine starts in semi- throttle position, engine speed will be fast enough for the clutch to engage the sprocket and turn the chain which may cause a kickback. Never attempt to start the saw when the guide bar is in a cut or kerf. When you pull the starter grip, don't wrap the starter rope around your hands. Do not allow the grip to snap back, but guide the starter rope slowly back to permit the rope to rewind properly. Failure to follow this procedure may result in injury to hand or fingers and may damage the starter mechanism. Important adjust men t s WARNI NG! At correct idle speed, chain should not turn. For di- rections to adjust idle speed, see the appropriate section of this instruction manual. Do not use a ...

Scarica la tua

Per scaricare, digitare 2 cifre :