Log:
valutazioni - 5, GPA: 4.2 ( )

Istruzioni per l'uso McCulloch, Modello Electramac EL35

Produttore : McCulloch
File Size : 950.21 kb
File Nome :
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


. The felling cut that provokes the tree fall, is performed at 3 to 5 cm above the lower part of the directional felling cut line, finishing at a distance of 1/10 of the trunk from the notch. Remain on the left hand side of the tree and cut using the chain pulling method and the spiked bumper. Check that the tree does not move in a direction other than that predicted for the fall. As soon as possible insert a felling lever or wedge into the cut. The uncut part of the trunk is called the “hinge”, as it is intended to guide the tree as it falls; in cases where the cuts are not sufficient, not straight, or have been cut through completely, the tree fall cannot be controlled (extremely dangerous!). For this reason the various cuts must be performed with great precision. When cutting operations are completed the tree will begin to fall. Where necessary help tree fall using wedges or felling levers . Limbing Once the tree has been felled, the trunk must be limbed: in other words, the branches are removed from the trunk. Do not underestimate this operation because the large majority of kickback accidents occur during this stage. For this reason pay close attention to the position of the bar nose during cutting operations and always work on the left hand side of the trunk. I. ENVIRONMENTAL INFORMATION This section contains information useful for maintaining the characteristic of ecocompatibility included in the origin design of the machine, and as regards proper use and disposal of chain oil DESIGN In the design stage, care was taken to develop an engine with reduced consumption and low emission of noise. USE OF THE MACHINE The operations of filling the oil tank should be carried out in such a way as to avoid spilling oil and contaminating the soil and the environment. DISPOSAL Do not dispose inappropriately of the machine when it is no longer usable. Deliver it to an authorized organization for proper disposal in compliance with the regulation in force. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council office, your household waste disposal service or the shop where you purchased the product. ENGLISH - 10 M. TROUBLESHOOTING TABLE Motor does not start Motor turns with difficulty or loses power The machine starts but does not cut properly Motor turns improperly or at reduced speeds Braking devices do not stop the chain properly Make sure the main line is powered ..• • • • • Make sure the machine is properly plugged in ..• • • • • Make sure your cable/ext. cord is not damaged ..• • • • • Make sure that chain brake is not activated ..• • • • • Check that chain is properly assembled • ..• • • Check chain lubrification as in chapters F and G ..• • • Make sure that the chain is sharp ..• • • Contact your authorised centre • • • • ENGLISH – 11 N. DECLARATION OF CONFORMITY The undersigned, authorized by H.O.P.I., declares that the following products model: type ES15, ES 15/1, ES 15/2, ES16, ES 16/1, ES18 starting from 2004 onwards, manufactured by H.O.P.I., Valmadrera, Italy, comply with European Directive: 98/37/EEC (Machine Directive), 93/68/EEC (EEC Marking Directive) & 89/336/CEE (Electromagnetic Compatibility Devices), directive 2000/...

Questo manuale è adatto anche per i modelli :
Benzo e seghe - Electramac 1650-14 (950.21 kb)
Benzo e seghe - Electramac 249498 (950.21 kb)
Benzo e seghe - Electramac EL1641 (950.21 kb)
Benzo e seghe - Electramac ES1814 (950.21 kb)

Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie