valutazioni - 4, GPA: 3.3
(
)
)
|
Facilità d'uso
If chain is backwards, saw will vibrate badly and will not cut. 9. Adjust saw chain tension. Follow steps guide bar nose (see Figure 3). under Saw Chain Tension Adjustment, page 7. Tapping Front Hand Mounting Stand-Outs Guide Bar Bolts Guide Bar Nuts Adjusting Hole Guide Bar Screw Saw ChainCutting Edge Cutting Edge Towards Guide Bar Nose Guard Drive Sprocket Figure 3 - Assembling Guide Bar, Chain, and Hand Guard Adjusting Block Adjusting Plate Adjusting Screw Sprocket Support Figure 4 - Part Locations For Assembling Guide Bar 6 097017 097017 7 OWNER’S MANUAL PUSH TO SHARPEN INSTALLING AUTOMATIC CHAIN SHARPENER (Fast Sharp Models Only) 1. Screw automatic chain sharpener into threaded hole. 2. Continue turning automatic chain sharpener until you hear five (5) clicks. Automatic Chain Sharpener Figure 5 - Automatic Chain Sharpener (Fast Sharp Models Only) ASSEMBLY Continued Note: For pre assembled models, the saw chain tension is properly set at factory. A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Follow steps below to readjust saw chain tension. 1. Before adjusting chain, make sure guide bar nuts are only finger tight (see Figure 3, page 6). Also make sure adjusting block is in oval adjusting hole on guide bar (see Figures 3 and 4, page 6). 2. Turn adjusting screw clockwise until all slack is out of chain (see Figure 6). Note: There should be no gap between side links of chain and bottom of guide bar (see Figure 7). 3. Wearing protective gloves, move chain around guide bar. Chain should move freely. If chain does not move freely, loosen chain by turning adjusting screw counterclockwise. 4. After chain tension is correct, tighten guide bar nuts firmly. If not, guide bar will move and loosen chain tension. This will increase the risk of kickback. This can also damage saw. Note: A new chain will stretch. Check new chain after first few minutes of operation. Allow chain to cool down. Readjust chain tension. SAW CHAIN TENSION ADJUSTMENT WARNING: Unplug chain saw from power source before adjusting saw chain tension. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. WARNING: Maintain proper chain tension always. A loose chain will increase the risk of kickback. A loose chain may jump out of guide bar groove. This may injure operator and damage chain. A loose chain will cause chain, guide bar, and sprocket to wear rapidly. Figure 6 - Turning Adjusting Screw Guide Bar Correct Tension Guide Bar Gap Incorrect Tension Guide Bar Nuts Figure 7 - Saw Chain Adjustment 1. Remove oil cap. 2. Fill oil tank with SAE #30 motor oil. Note: For temperatures below 30°F, use SAE #10 oil. For temperatures above 75°F, use SAE #40 oil. 3. Replace oil cap at once. Tighten oil cap firmly for good seal. This will avoid oil seepage from tank. 4. Wipe off excess oil. Note: It is normal for oil to seep when saw is not in use. Empty oil tank after each use to prevent seepage. FILLING OIL TANK ® ELECTRIC CHAIN SAW OPERATING CHAIN SAW WARNING: Read and understand this owner’s manual before operating this saw. Make certain you read and understand allSafety Warnings, pages 2 and 3. Improper use of this chain saw can cause severe injury or death from fire, electrical shock, or body contact with moving chain, or falling wood. EXTENSION CORDS Use proper extension cords with this saw. Use only extension cords marked for outdoor use. The cord must be marked with suffix W or W-A following the cord type designation. Example:SJTW-A or SJTW. Use proper sized cord with this saw. Cord must be heavy enough to carry current needed. An undersized cord will cause voltage drop at saw. Saw will lose power and overheat. Follow cord size requirements listed below. Cord AWG Cord Length Size 25 feet 16 50 feet 16 100 feet 14 150 feet 12 Keep cord away from cutting area. Make sure cord does not catch on branches or logs during cutting. Inspect cords often. Replace damaged cords. The extension cord may come undone from the power cord during use. To avoid this, make a knot with the two cords as shown in Figure 8 below. Extension Chain Saw Cord Power Cord OILING CHAIN Always check oil level before using saw. To oil chain, press oil cap. Do not attempt to operate the oiler while cutting with the saw. Oil will feed onto guide bar and chain. Press oil cap at least once before each cut. Check oil level often by looking at oil sight level hole. Oil sight level hole is on left side of saw, between front handle and front hand guard. Figure 9 - Pressing Oil Cap to Oil Chain CUTTING WITH THE CHAIN SAW 1. Connect saw to extension cord. Connect extension cord to power supply. 2. Make sure section of log to be cut is not laying on ground. This will keep chain from touching ground as it cuts through log. Touching ground with moving chain will dull chain. 3. Use both hands to grip saw. Always use left hand to grip front handle and right hand to grip rear handle. Use firm grip. Thumbs and fin...
Questo manuale è adatto anche per i modelli :Benzo e seghe - 076728J, 100089-06, 099178H EL-1, 075762J, 098031J, 099039J, 100015, 100089-01, 100089-04, 100089-05 (606.94 kb)
Benzo e seghe - 076728J, 100089-06, 099178H EL-1, 075762J, 098031J, 099039J, 100015, 100089-01, 100089-04, 100089-05 (606.94 kb)
Benzo e seghe - 076728J, 100089-06, 099178H, 075762J, 098031J, 099039J, 100015, 100089-01, 100089-04, 100089-05, 100 (606.94 kb)
Benzo e seghe - 076728J, 100089-06, 099178H, EL-1, EL-7, 075762J, 098031J, 099039J, 100015, 100089-01, 100089-04,100 (606.94 kb)