valutazioni - 2, GPA: 3
(
)
)
|
Facilità d'uso
Removebarclamp. DriveSprocket Bar Knob Bar Clamp 8. Pull guide bar forward until the chain CHAIN ADJUSTMENT is snug in the guide bar groove. Ensure all drive links are in the bar groove. 9. Install bar clamp. Be sure adjusting pin is in the adjusting pin hole in the guide bar. CAUTION: It is very important when installing the bar clamp that the adjusting pin aligns into the adjusting pin hole in the bar. Failure to install the bar clamp correctly may result in permanent damage to your chain saw. BackviewofbarclampAdjustingpin See CHECK CHAIN TENSION in the MAINTENANCE section. CUSTOMER SERVICEABLE PARTS WARNING: Use of any other accessory or attachment might present a risk of injury to the operator. REPLACEMENT PART PART NO. Oil Cap Chain Catcher Screw File (5/32. dia.) Twin Pak Chain - -- 18. Guide Bar - -- 18. Bar & Chain Lubricant - -- 1 qt. Bar & Chain Lubricant - -- 1 gal. 530053072 530029850 530016269 952055085 952051338 952044418 952030203 952030204 10. Install bar knob; finger tighten only. Do not tighten any further at this point. Proceed to CHAIN ADJUSTMENT. STORAGE WARNING: Perform the following steps after each use: S Allow motor to cool before storing or transporting. S Store chain saw and extension cord in a well ventilated area S Store chain saw with all guards in place and position chain saw so that any sharp object cannot accidentally cause injury. S Store chain saw unplugged, well out of the reach of children. SEASONAL STORAGE Prepare your unit for storage at the end of the season or if it will not be used for 30 days or more. If your chain saw is to be stored for a period of time: S Clean it thoroughly before lengthy stor age. S Store in a clean dry area. S Lightly oil external metal surfaces and guide bar. S Oil the chain and wrap it in heavy paperorcloth. 16 TROUBLESHOOTING TABLE WARNING: Always stop unit and disconnect from the power source before performing all of the recommended remedies below except remedies that require unit to be operating. TROUBLE Chain does not move when trigger switch is engaged. Chain clatters or cuts roughly. Chain stops during cut. Oil inadequate for bar and chain lubrication. Chain cuts at an angle. CAUSE 1. Chain tension incorrect. 2. Guide bar rails pinched. 3. Trigger switch failure. 4. Circuit breaker tripped/ fuse failure. 1. Chain tension incorrect. 2. Cutters damaged. 3. Chain worn. 4. Cutters dull, improperly sharpened, or depth gauges too high. 5. Sprocket worn. 1. Chain cutter tops not filed flat. 2. Guide bar burred or bent; rails uneven. 1. Oil tank empty. 2. Oil outlet clogged. 3. Guide bar oil hole blocked. 1. Cutters damaged on one side. 2. Chain dull on one side. 3. Guide bar bent or worn. REMEDY 1. See “Check Chain Tension” in Maintenance section. 2. Repair or replace. 3. Contact an authorized service dealer. 4. Reset circuit breaker or replace fuse. 1. See “Check Chain Tension” in Maintenance Section. 2. Contact an authorized service dealer. 3. Resharpen or replace chain. 4. See “Chain Sharpening” in Service and Adjustments section. 5. Contact an authorized service dealer. 1. See “Chain Sharpening” in Service and Adjustments section. 2. Repair or replace guide bar. 1. Fill oil tank. 2. Contact an authorized service dealer. 3. Remove bar and clean. 1. See “Chain Sharpening” in Service and Adjustments section. 2. See “Chain Sharpening” in Service and Adjustments section. 3. Replace guide bar. 17 WARRANTYSTATEMENTWARRANTYSTATEMENT Poulan, a division of Husqvarna Consumer Outdoor Products N.A., Inc., warrants to the original consumer purchaser that each new Poulan brand electric or cordless product is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective Poulan brand electric product within one (1) year from the original date of purchase. If your Poulan brand electric or cordless product should fail within the limited warranty period, you may return it in complete condition, prepaid, with proof of purchase to the dealer from whom it was purchased for repair or replacement at the option of Poulan. This warranty is not transferable and does not cover damage or liability caused by improper handling, improper maintenance or alteration, or the use of accessories and/or attachments not specifically recommended by Poulan for this product. This warranty does not cover parts that will wear and require replacement with reasonable use during the warranty period. This warranty does not cover pre- --delivery setup or normal adjustments explained in the instruction manual. Should you have any unanswered questions regarding this warranty, please contact: Poulan, a division of Husqvarna Consumer Outdoor Products N.A., Inc. 7349 Statesville Road Charlotte, NC 28269 1- --800- --554- --6723 In Canada, contact: Poulan 850 Matheson Blvd. West Mississauga, Ontario L5V 0B4 Giving the model number, serial number and date of purchase of your product and the name and address of the authorized dealer from whom it...