valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
If the chain is too loose, it will sag below the bar. tGuideBarChainAdjustmenBar Nuts Adjusting Tool (Bar Tool) Screw Adjusting the tension: Chain tension is very important. Chains stretch during use. This is especially true during the first few times you use your saw. Always check chain tension each time before you start the chain saw. 1. Loosen bar nuts until they are finger tight against the clutch cover. 2. Turn adjusting screw clockwise until chain solidly contacts bottom of guide bar rail. AdjustingScrew 7 3. Using bar tool, roll chain around guide bar to ensure all links are in bar groove. 4. Lift up tip of guide bar to check for sag. Release tip of guide bar, then turn adjusting screw 1/4 turn clockwise. Repeat until sag does not exist. Adjusting Screw - --1/4 Turn 5. While lifting tip of guide bar, tighten bar nuts securely with the bar tool. BarNuts 6. Use the screwdriver end of the bar tool to move chain around guide bar. 7. If chain does not rotate, it is too tight. Slightly loosen bar nuts and loosen chain by turning the adjusting screw 1/4 turn counterclockwise. Retighten bar nuts. 8. If chain is too loose, it will sag below the guide bar. DO NOT operate the saw if the chain is loose. NOTE: The chain is tensioned correctly when the weight of the chain does not cause it to sag below the guide bar (with the chain saw sitting in an upright position), but the chain still moves freely around the guide bar. WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury to the operator and/or damage the chain making it unusable. If the chain jumps off the guide bar, inspect each drive link for damage. Damaged chain must be repaired or replaced. OPERATION KNOW YOUR CHAIN SAW READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR CHAIN SAW. Compare the illustrations with your unit to familiarize yourself with the location of the various controls and adjustments. Save this manual for future reference. ChainAdjustmentTool(BarTool) PrimerBulbBarOilFillCapChainFrontHandGuardFrontHandleStarterRopeON/STOPSwitchMufflerChoke/ FastIdleLeverBarSprocketHole Starter Housing Fuel Mix Fill Cap Rear Handle Throttle Clutch Cover Catcher Trigger GuideBarBarNutsCylinderCoverThrottleLockoutChainBrakeChainDirectionofTravelAdjustingScrewChain ON/STOP SWITCH THROTTLE TRIGGER The ON/STOP SWITCH is used to stop the The THROTTLE TRIGGER controls engine engine. speed. 8 THROTTLE LOCK- --OUT The THROTTLE LOCK- --OUT must be pressed before you can squeeze the throttle trigger. This feature prevents you from accidentally squeezing the trigger. CHOKE/FAST IDLE LEVER The choke and fast idle are set by pulling the CHOKE/FAST IDLE LEVER out to the full extent for cold starting or after refueling. The choke provides additional fuel to the engine during cold starting. PRIMER BULB The PRIMER BULB circulates fuel to the carburetor to provide quicker starting. CHAIN BRAKE The chain brake is a device designed to stop the chain if kickback occurs. The chain brake activates automatically in the event of kickback. The chain brake activates manually if the front hand guard is pushed forward. The chain brake is disengaged by pulling the front hand guard back toward the front handle as far as possible. CHAIN TENSION It is normal for a new chain to stretch during the first 15 minutes of operation. You should check your chain tension each time before you start the chain saw. See CHAIN TENSION under the ASSEMBLY section. WARNING: If the saw is operated with a loose chain, the chain could jump off the guide bar and result in serious injury to the operator and/or damage the chain making it unusable. BEFORE STARTING ENGINE WARNING: Muffler is very hot during and after use. Do not touch the muffler or allow combustible material such as dry grass or fuel to do so. WARNING: Be sure to read the fuel handling information in the safety rules section of this manual before you begin. If you do not understand the fuel handling information do not attempt to fuel your unit. Seek help from someone that does understand the information or call the customer assistance help line at 1-800-554-6723. FUELING ENGINE WARNING: Remove fuel cap slowlywhenrefueling. HELPFULTIPToobtainthecorrectoilmixratio,pour3.2ouncesof2--cyclesyntheticoilintoonegallonoffreshgas. This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air- cooled engine oil designed to be mixed at a ratio of 40:1. Poulan/WEED EATER brand synthetic oil is recommended. A 40:1 ratio is obtained by mixing 3.2 fluid ounces (95 ml) of oil with 1 gallon (4 liters) of unleaded gasoline. Included with this saw is a 3.2 ounce (95 ml) container of Poulan/WEED EATER brand synthetic oil. Pour the entire contents of this container into 1 gallon (4 liters) of gasoline to achieve the proper fuel mixture. DO NOT USE automotive or marine oil. These oils will cause engine damage....