ON/STOPSWITCH CHOKE/FASTIDLELEVERFULLHALFOFF STARTING A WARM ENGINE 1. Move ON/STOP switch to the ON position. 2. Pull the choke/fast idle lever out to the HALF CHOKE position. 3. Pull the starter rope sharply with your right hand until the engine starts. 4. Squeeze and release the throttle trigger to allow engine to return to idle speed. DIFFICULT STARTING (or starting a flooded engine) The engine may be flooded if it has not started after 10 pulls. Flooded engines can be cleared of excess fuel

02 PLATE 1 32 MC-6SDABB03-18 SCREW 1 66 MC-6SLABB03-06 SCREW 33 MC-6228-210105 OIL PUMP ASS'Y 1 67 MC-6010-211301 WIRE 1 34 MC-6188-211501 PULL BAR 1 68 MC-6SDABB04-14 SCREW 3 35 MC-6114-211501 PULL PLATE 1 Stocking Codes are: A - Dealer stocked B - Distributor stocked C - Factory stocked

This sudden stopping pulls the saw forward and away from the operator and could easily cause the operator to lose control of the saw. Avoid Pinch- --Kickback: S Be extremely aware of situations or obstructions that can cause material to pinch the top of or otherwise stop the chain. S Do not cut more than one log at a time. S Do not twist the saw as the bar is withdrawn from an undercut when bucking. Avoid Pull- --In: S Always begin cutting with the engine at full speed and the saw housing agains

ageing. 6. Remove plug from mains before passing 3. Do not use the Hedgetrimmer if the electric Hedgetrimmer to another person. cables are damaged or worn. 7. Avoid operating while people especially chil4. Immediately disconnect from the mains elec-dren are nearby. tricity supply if the cable is cut, or the insula-8. Whilst using the Hedgetrimmer always be tion is damaged. Do not touch the electric sure of a safe and secure operating position. cable until the electrical supply has been dis-9. Ke

2. Check that all nuts and bolts are secure. 3. Visually inspect the Hedgetrimmer for any worn or damaged parts, contact your local Service Centre if any parts require replacement. To store your Hedgetrimmer • The Hedgetrimmer blade cover/storage holder is provided with 2 hanging slots for storing the Hedgetrimmer on the wall.(See Pic L) • Ensure the blade cover/storage holder is fitted before storage. 1. The use of 2 number 10 screws (40mm in length) and the appropriate wall fixing plugs is rec

All of the centres listed stock genuine Electrolux Spare Parts. NOTE: Our Service Repairers act on their own behalf and are not empowered to commit or legally bind Electrolux Outdoor Products in any manner whatsoever. Declaration of Conformity I, the undersigned M. Bowden of Electrolux I, the undersigned M. Bowden of Electrolux I, the undersigned M. Bowden of Electrolux Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial Park, Outdoor Products, Aycliffe Industrial P

ageing. 6. Remove plug from mains before passing 3. Do not use the Hedgetrimmer if the electric Hedgetrimmer to another person. cables are damaged or worn. 7. Avoid operating while people especially chil4. Immediately disconnect from the mains elec-dren are nearby. tricity supply if the cable is cut, or the insula-8. Whilst using the Hedgetrimmer always be tion is damaged. Do not touch the electric sure of a safe and secure operating position. cable until the electrical supply has been dis-9. Ke

Guarantee & Guarantee Policy If any part is found to be defective due to faulty manufacture within the guarantee period, Electrolux Outdoor Products, through its Authorised Service Repairers will effect the repair or replacement to the customer free of charge providing: (a) The fault is reported directly to the Authorised Repairer. (b) Proof of purchase is provided. (c) The fault is not caused by misuse, neglect or faulty adjustment by the user. (d) The failure has not occurred through fair wear

3. Visually inspect the Hedgetrimmer for any worn or damaged parts, contact your local Service Centre if any parts require replacement. To store your Hedgetrimmer • The Hedgetrimmer blade cover/storage holder is provided with 2 hanging slots for storing the Hedgetrimmer on the wall.(See Pic L) • Ensure the blade cover/storage holder is fitted before storage. 1. The use of 2 number 10 screws (40mm in length) and the appropriate wall fixing plugs is recommended 2. Drill 2 holes 47mm horizontally a