(SA1) ¦ FELLING A TREE (SA2) WARNING SA2 When you fell a tree, be sure to warn your neighboring workers of the danger. 1. Decide the felling direction considering the wind, Iean of the tree, location of heavy branches, ease of job after felling, and other factors . 2. While clearing the area around the tree, arrange a good foothold and retreat path. 3. Make a notch cut one-third of the way into the tree on the felling side. 4. Make a felling cut from the opposite side of the notch and at a level

(MA11) For a replacement plug, use Champion RCJ- 6Y(noise-proof) or CJ-6Y, or NGK BPMR7A. DRIVE SPROCKET Periodically check the drive sprocket for wear and damage, and replace when the teeth have worn over 0.04 inch, or when any damage has been observed. (MA12) HANDLE MOUNTING JOINTS Inspect the handle mounting joints and replace when any adhered part is peeled off or a crack is observed on the rubber part. Also replace when the inside of the rear damper metal has worn remarkably. .19. 9. Mainte

Always ensure your foothold as well as stability of the tree. 2. Be alert to the rolling over of a cut log. 3. Read the instructions in “For Safe Operation” to avoid kickback of the saw. Before starting work, check the direction of bending force inside the log to be cut. Always finish cutting from the opposite side of bending direction to prevent the guide bar from being caught in the cutaway. • Cutting an unpillowed log Saw down halfway, then roll the log over and cut from the opposite side. •

G2500TS Fig.2 CARBBURETOR COMPONENTS & ACCESSORIES (S/N 010101 and up) Q'TY Key# PART NUMBER DESCRIPTION NOTE /UNIT 1 T2040-81000 CARBURETOR ASS'Y 2 2630-81120 • PUMP COVER 1 3 3310-81130 • SCREW 1 4 3310-81280 • COVER 1 1480-81420 • PLUG 1 6 3350-81380 • SPRING 1 7 2630-81330 • SCREW 1 8 2880-81470 • SCREW 1 9 3310-81341 • VALVE 1 2670-81410 • SPRING 1 11 T2040-81370 • SHAFT ASS'Y 1 12 2841-81440 • LEVER 1 13 1148-81390 • RING 1 14 3310-81360 • SCREW 1 3310-81351 • SCREW 4 16 2841-06030 • REBUI

Be sure to refill the oil tank everytime when refueling the saw. Adjusting carburetor The carburetor has been adjusted at the factory. Should your unit need readjustment due to the changes in altitude or operating conditions, please let your skillful dealer make the adjustment. A wrong adjustment may cause damage to your unit. If you have to make the adjustment yourself, please follow the procedure below carefully. e sure to adjust the carburetor with the bar chain attached. 1. Stop engine a

Move the chain saw at least ten (10) feet (three (3) m) from the fueling point before starting the engine. 4. Do not allow other persons to be near the chain saw when starting or cutting, keep bystanders and animals out of the work area. 5. Never start cutting until you have a clear work area, secure footing, and a planned retreat path from the falling tree. 6. Always hold the chain saw firmly with both hands when the engine is running. Use a firm grip with thumb and fingers encircling the ch

[It is possible that some specific parts may be subject to change of their delivery term and list price within the limit of ten (10) years after the machine is discontinued. And it is also possible that some parts may be available even after the limit of ten (10) years.] APPLICABLE SERIAL NUMBERS : 100101 and up Nov. 2001 G451/G4500/G5000 Fig.1 POWER UNIT Fig.1 POWER UNIT G451/G4500 Key# PART NUMBER DESCRIPTION Q'TY /UNIT NOTE 1 2670-12113 Cylinder 1 043 2 2810-14110 Inlet Pipe 1 3 28

Before each use, check that the net is attached in place and is free from any damage. WARNING IMPORTANT Maintenance .15 . • Note that using any spark plugs other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged. • To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench. IMPORTANT Disposal • When disposing your machine, fuel or oil for the machine, b