valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Once the isolator is removed, the control panel will announce the sensor's status, such as "Zone 1 Sensor 1 Triggered", and corresponding zone LED will flash and buzzer will beep. If the magnetic contact is closed, the beeping will stop. Note: - Both Window/Door Sensors have been programmed at the factory. They are Zone 1 Sensor 1 and Zone 2 Sensor 1. Trigger the sensor and listen to the announcement to determine which one is zone 1 and which is zone 2. Testing: After mounting the sensor, test the sensor by opening and closing the door or window. Open the door or window will result in the followng: 1. Voice announcement - Announce the triggered zone and sensor. 2. Beeping - The number of beep represents the zone number. 3. Zone LED flashing - Number of flash represents the sensor number. Mounting the Sensor The transmitters should be mounted on the door frame or window frame by double sided tape. The magnet should be mounted on the door or window by either double sided tape or screws. Make sure the magnet is aligned with the red marking on the transmitter. If the surface of the frame is flat enough, doublesided foam tape is sufficient, otherwise, it is recommended to screw the mounting plate to the frame, then apply double sided tape. After mounting the sensor, if the AAA+ logo is inverted, remove the front cover and rotate it so the AAA+ logo is in the upright position. INSTALLATION (ML-100 Only) Installing Door / Window Sensors Transmitter Magnet Double-sided foam tape Mounting plate and screws (optional) Sensor Sensor Sensor Magnet Magnet "Red Marking" "Red Marking" Magnet on the left Magnet on the right IINNSSTTAALLLLAATTIIOONN ((MMLL--110000 OOnnllyy)) HOOMME AAUUTOMATTIION Part 1 Learn signal from Control Module to Control Panel Note: -Try to mount the sensors as far away from the floor as possible to avoid damaging them. Mounting the sensors at a higher position will also result in better operating range. -Do not mount the sensor to the exterior of the door / window, always mount the sensor to the interior side of the door / window to avoid being damaged or stolen by non-intended users. Installing Motion Sensor The motion sensor is most suitable for guarding a large area such as living room, family room, or bedroom. It can also be used to monitor a hallway or stairway. 3. Single flash1. Zone 1 Sensor 1 Triggered 2. Beep___Beep___ Beep___Beep___ ............ 1 2 3 4 [PROG] [MPIN] Enter Programming mode Enter master password to programming mode 3 beeps for valid password. 1 long beep for invalid password. Select learn control module programming [1] to [5] After you have selected the control module location, that zone LED will be on. After [4] is entered, some zone LEDs will flash or stay off. The zone LEDs represent whether that zone is already occupied by another control module.**See Table E. Select control module location (Max. 5 control modules) Select the location [1], [2], [3], [4], or [5]. Send signal from control module to control panel. Once the signal is transmitted to the Control Panel, that signal will be stored. You will hear [Device X Accepted], where “X” is the control module location. [4] Step Keys Function Description Note Insert Battery Undo the screw on the back of the motion sensor and remove the battery cover. Connect a 9V alkaline battery to the battery connector. Please note the polarity. If you are planning to install the motion sensor outdoor, you should reduce the sensitivity by placing the jumper at location “2”. For indoor application, if you want to reduce the sensitivity, you can change the jumper setting to “2” as well. Sensitivity Jumper Location 1 High Sensitivity Jumper Location 2 Low Sensitivity ZONE LED DESCRIPTION Off Zone is not occupied by any control module Flashes once This zone is occupied by another control module. Programming another remote to this zone will overwrite the previous control module. Flashes twice This zone is occupied by a remote. You can still program a control module to this zone, and it will not overwrite the remote you have in this zone. Flashes once, then twice This zone is occupied by a remote AND a control module. If you program another control module to this zone, it will overwrite the previous control module, but not the remote. Caution: ** Table E: Zone LED status for learning control module. Depending on the environment, if you experience a false trigger when the motion sensor is placed outdoors, you should relocate it or even place it indoors. Wind blowing at a tree, or direct sunshine could cause a false trigger. Therefore, if the location at where the motion sensor is mounted could cause a false trigger, you should change the mounting location for such sensor. –16––41– –17– The Control Panel can be used to control lights and home applicances with a Control Module, (Control Module is sold separately). Garage door opener can be controlled with a Garage Door Receiver (sold separately). The Control Panel can control up to 5 Control Modu...
Questo manuale è adatto anche per i modelli :cuffie wireless e altri accessori - MULTI LINK PRO ML-001 (746.93 kb)