valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
hides fingerprints. ensures operating is filled to capacity. Sealing Ring 6 7 Assembling Your Blender 1. Before assembling your blender wipe blender base with a warm sudsy cloth, then wipe clean with a damp cloth. Dry with a soft cloth. Wash blender jar, lid, collar and blades in warm, sudsy water. Rinse and wipe parts dry. 2. Turn blender jar upside down. Place the small sealing ring on the blade assembly. 3. Place the blade assembly with the sealing ring in the bottom opening of the jar. WARNING Electrical Shock Hazard Do not put in water. Failure to do so can result in death or electrical shock. 4. Twist collar onto jar. Be sure to engage threads properly and securely. Turn assembled jar right side up. 5. Place lid onto blender jar. 8 1 mlml 1000 750 500 250 liters 1 3 4 1 2 1 4 8 6. Coil the power cord into the storage area on the bottom of the power base to shorten. 7. Place jar on power base. 8. Plug power cord into a grounded 3-prong outlet. Blender is now ready to use. 9. Before removing the jar from the base after use, always push the OFF pad and make sure the blinking red light is off, then unplug. Lift the jar straight up, with the collar attached, do not twist. Do not unscrew the glass jar from the collar until you are ready to remove the blade assembly. Loosening the collar with liquids inside the jar will cause them to leak out. Assembling Your Blender Ultra Power Control mlml 1000 750 500 250 liters 1 3 4 1 2 1 4 Stir Mix Liquefy Off On Pulse Ice Crushing All Speeds WARNING:FLASHINGLIGHTINDICATESREADYTOOPERATE DONOTTOUCHBLADES Ultra Power mlml 1000 750 500 250 liters 1 3 4 1 2 1 4 WARNING Electrical Shock Hazard Plug into a grounded 3 prong outlet. Do not remove ground prong. Do not use an adapter. Failure to follow these instructions can result in death, fire or electrical shock. 9 To Operate Your Blender NOTE: While red indicator light is blinking or blender is on: - Do not touch blades. - Do not interfere with blade movement. - Do not remove blender jar lid. •With red light flashing, an accidental touching of a speed pad, or other circumstances may result in turning on the blender. • If blender runs when ON light is flashing, do not use. Take unit to an Authorized Service Center. (However a slight flicker is normal.) • This unit should operate only when a speed pad is pressed. Immediately press the OFF pad if the unit runs at any other time. If this occurs, do not use; take the unit to an Authorized Service Center. The KitchenAid® Classic blender has three speeds: Stir, Mix and Liquefy. • Before operating the blender, make sure the blender jar is properly assembled (see page 7) and in place on the blender base. Put ingredients in jar and firmly attach lid. • Press the ON pad. The red indicator light should blink on and off indicating the speed pads are activated. NOTE: If the red indicator light is not blinking at this time, unplug blender and take unit to an Authorized Service Center. • Press the desired speed pad for continuous operation at that speed. The indicator light will glow and the red light will stay on. You may change speeds without stopping the unit by pushing the new speed pad. • If blending warm foods or liquids, place a cloth over the blender lid and operate only on STIR speed. Do not place bare hand over blender lid. • To turn the blender off, press the OFF pad. The OFF pad will stop any speed and deactivate the blender at the same time. Before removing the blender jar, deactivate the blender by pressing the OFF pad and unplugging the power cord. NOTE: Do not overprocess foods. Stop and check the consistency of foods after a few seconds. Control Stir Mix Liquefy Off On Pulse Ice Crushing All Speeds WARNING: FLASHING LIGHT INDICATES READY TO OPERATE DO NOT TOUCH BLADES Control Stir Mix Liquefy Off On Pulse Ice Crushing All Speeds WARNING: FLASHING LIGHT INDICATES READY TO OPERATE DO NOT TOUCH BLADES Control Stir Mix Liquefy Off On Pulse Ice Crushing All Speeds WARNING:FLASHINGLIGHTINDICATESREADYTOOPERATE DONOTTOUCHBLADES mlml 1000 750 500 250 liters 1 3 4 1 2 1 4 mlml 1000 liters 1 10 Ingredient Cap Remove cap and add ingredients at STIR or MIX speeds. When operating at higher speeds, with a full jar or with hot contents, stop blender and add ingredients. Step Start® Feature Step Start® feature automatically starts the blender at a lower speed to prevent splattering then quickly increases to the selected speed for optimal performance. Pulse Feature Your KitchenAid® blender has a “Pulse At Any Speed” feature. • Before operating the blender, make sure the jar is properly assembled (see page 7) and in place on the blender base. Put ingredients into blender jar and attach lid firmly. • Press the ON pad. The red indicator light should be blinking, showing that the blender is activated. • Press the PULSE pad. The indicator light above the pad will glow, indicating that all the speed pads are in the Pulse mode. • Select a speed pad and press for the desired length of time (a short...