valutazioni - 3, GPA: 3.3 ( )

Produttore : Sony File Size : 2.51 mb File Nome : Lingua di insegnamento:

Foto e specifiche   Sony  BDV-E980

64US IMPORTANT NOTICE IMPORTANT NOTICE On moving the system • Before moving the system, make sure that there is no disc inserted, and remove the AC power cord (mains lead) from the wall outlet (mains). Notes about the Discs On handling discs • To keep the disc clean, handle the disc by its edge. Do not touch the surface. • Do not stick paper or tape on the disc. • Do not expose the disc to direct sunlight or heat sources such as hot air ducts, or leave it in a car parked in direct sunlight as the temperature may rise considerably inside the car. • After playing, store the disc in its case. On cleaning • Before playing, clean the disc with a cleaning cloth. Wipe the disc from the center out. • Do not use solvents such as benzine, thinner, commercially available cleaners, or anti-static spray intended for vinyl LPs. This system can only play a standard circular disc. Using neither standard nor circular discs (e.g., card, heart, or star shape) may cause a malfunction. Do not use a disc that has a commercially available accessory attached, such as a label or ring. Additional Information 65US Troubleshooting Troubleshooting g guide to help remedy the problem before requesting repairs. Should any problem persist, consult your nearest Sony dealer. Note that if service personnel changes some parts during repair, these parts may be retained. General Symptom Problems and solutions The power is not turned on. • Check that the AC power cord (mains lead) is connected securely. The remote does not function. • The distance between the remote and the unit is too far. • The batteries in the remote are weak. The disc tray does not open and • Try the following: 1 Press and hold N and Z on the unit for more than 5 you cannot remove the disc even seconds to open the disc tray. 2 Remove the disc. 3 Disconnect the AC power after you press Z. cord (mains lead) from the wall outlet (mains), then reconnect after several minutes. The system does not work • Disconnect the AC power cord (mains lead) from the wall outlet (mains), then normally. reconnect after several minutes. Messages Symptom Problems and solutions [A new software version is • See [Network Update] (page 57) to update the system to a newer software available. Please go to the version. “Setup” section of the menu and select “Network Update” to perform the update.] appears on the TV screen. “PROTECTOR” and “PUSH PWR” appear alternately in the front panel display. Press "/1 to turn off the system, and check the following items after “STANDBY” disappears. • Are the + and – speaker cords short-circuited? • Are you using only the specified speakers? • Is anything blocking the ventilation holes of the system? • After checking the above items and fixing any problems, turn on the system. If the cause of the problem cannot be found even after checking all the above items, consult your nearest Sony dealer. “LOCKED” appears in the front • Set the child lock function to off (page 51). panel display. “DEMO LOCK” appears in the • Contact your nearest Sony dealer or local authorized Sony service facility. front panel display. “Exxxx” appears in the front • Contact your nearest Sony dealer or local authorized Sony service facility and panel display. give the error code. appears without any • Contact your nearest Sony dealer or local authorized Sony service facility. messages on the entire TV screen. 66US Picture Picture There is no picture. • Check the output method on your system (page 22). There is no picture when you • The unit is connected to an input device that is not HDCP (High-bandwidth make an HDMI cable Digital Content Protection) compliant (“HDMI” on the front panel does not connection. light up) (page 22). 3D images from the HDMI (IN • Depending on the TV or video component, 3D images may not appear. 1) or HDMI (IN 2) jack do not appear on the TV screen. There is no picture or output • When playing a BD-ROM, a high-resolution image may not be output because resolution is low when you make of copy protection limitations. We recommend to make a HDMI connection a component video cable (page 22). connection. No picture appears when the • Press and hold N and VOL – on the unit for more than 5 seconds to reset the video output resolution selected video output resolution to the lowest resolution. in [Output Video Format] is incorrect. The dark area of the picture is too • Set [Picture Quality Mode] to [Standard] (default) (page 41). dark/the bright area is too bright or unnatural. The picture is not output • Check the [Output Video Format] settings in [Screen Settings] (page 58). correctly. • If the analog and digital signals are output at the same time, set [BD/DVDROM 1080/24p Output] in [Screen Settings] to [Off] (page 59). • For BD-ROMs, check the [BD/DVD-ROM 1080/24p Output] settings in [Screen Settings] (page 59). Picture noise appears. • Clean the disc. • If the picture output from your system goes through your VCR to get to your TV, the copy-protection signal applied to some...

Scarica la tua

Per scaricare, digitare 2 cifre :