valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
Also, the protective sheet may be replaced in the CD-ROM pack to provide protection when the unit is moved or if it will not be used for an extended period of time. • Do not place items other than CDs on the tray. • Do not leave the tray in the open position or touch the lens area. Should the lens become soiled by dust or dirt, the unit may not read CDs properly. • Do not apply excessive force to the tray in the open position, doing so could damage the tray. • Do not open the CD-ROM drive or move the computer while the CD-ROM drive is being accessed. Doing so could cause it to malfunction. In addition, after running an application involving access to a CD, do not open the CD-ROM drive or remove the CD until after the application has been closed. • Cleaning the CD-ROM drive using a CD lens cleaner (except a liquid type cleaner) is recommended if it malfunctions. • Never insert foreign objects such as paper clips into the slot in the CD-ROM pack. • Do not touch the data surface as it can cause the CD to become dirty or scratched. To avoid damaging CDs: • Do not use CDs that have become deformed (warped, not completely round, etc.). • Do not allow CDs to become dirty or scratched. • Do not use the CD-ROM pack in a location where there is a lot of oily smoke or tobacco smoke. Doing so could shorten the service life of the lens. • Do not place or store CDs in locations exposed to heat, direct sunlight, humidity or dust. • Do not write on the surface of the CD with a ball-point pen or other writing instrument. • If the CD is brought from a cold into a warm environment, moisture may form on the disc. Wipe this moisture off with a soft, dry, lint-free cloth before using the CD. • Do not drop, bend, or place heavy objects on top of CDs. • Cleaning the CD using a CD disk cleaner (LF-K022DC) is recommended once every 2 or 3 months. If the CD gets dirty After wiping the CD with a moist, soft cloth, wipe it with a dry cloth. Always wipe from the center toward the edge. 5 Mounting the CD-ROM Pack 7Power Off your computer ((^"Operating Instructions" of the computer, "Shutting Down") Do not shut down using the suspend or hibernation mode. Г In the suspend or hibernation mode, do not remove/change the multimedia pocket device. Removing the device in the suspend or hibernation mode may damage the device. 2m Removing the device (Floppy disk drive) Cover (T) Turn your computer over and open the cover by sliding the latch. (2) Press the MP release button. The device will eject slightly. (3) Remove the device by holding both sides of the device. Г 91 Please handle the device as shown (holding both sides). Otherwise, the device may be damaged. Also, do not apply excessive downward force on the device. • Installing the device (CD-ROM Pack) Gently insert the device into the multimedia pocket by pushing on both comers until it clicks into place. MP Release Button 3 Power on your computer 4 Open the disc tray, and place a CD on it (J) Press the CD eject button and slowly pull out the tray. (2) Remove the lens protect sheet attached to the lens in the CD-ROM drive and place the CD securely on the center holder. (3) Close the tray. Side with title on top Eject button Center holder Do not apply excessive force to the tray in the open position, doing so could damage the trav. Software Preparation (first time only) The following settings are necessary to prepare the CD-ROM pack for use: 1 Add the check mark for [DMA] in [Start] - [Settings] - [Control Panel] - [System] - [Device Manager] - [CDROM] - [MATSHITA UJDA150] - [Settings]. 2 Set [L:] for both [Start drive letter] and [End drive letter] in [Reserved drive letters], then press [OK], 3 At the [System Properties], press [OK]. The display will ask you to restart Windows, select [Yes] to restart. Using the CD-ROM pack in the MS-DOS mode To use the CD-ROM pack in the MS-DOS mode, configure the drive following the steps below after performing the above steps I - 3. If the steps listed below are performed without completing steps 1-3 above first, the drive will not operate properly. 1 Click the [Start] button then select [Shut Down], 2 Select [Restart in MS-DOS mode] and click [OK], 3 Open the "CONFIG.SYS" file for editing by issuing the following commands: cd \( Enter ) edit config.sys ( Enter ) 4 Move the cursor to the line containing "ATAPICD.SYS" and delete the characters "rem" at the beginning of the line. (Deleting "rem" causes the item to become valid.) DEVICEHIGH=C:\WINDOWS\COMMANDVATAPICD.SYS/D:MSCDOOO (If this line is missing, add it.) 5 Pressf Altl +fin , thenflD to save the file. Then press i Alt) +QD, thenC X ) to exit the Edit program. 6 Follow the same steps to edit the "AUTOEXEC.BAT" file, edit autoexec.bat ( Enter 1 7 Move the cursor to the line containing "MSCDEX.EXE” and delete the characters "rem" at the beginning of the line. (Deleting "rem" causes the item to become valid.) LOADH1GH C:\WINDOWS\COMMAND\MSCDEX...