valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
If this happens, restart your computer. Note: • If you turn off the drive while your computer and the drive are connected, your computer will not be recognized the drive. To use the drive again turn on the drive or disconnect the USB cable and connect it again. 22 Inserting / Removing a Disc Inserting a disc (T) Slide the OPEN lever to open the disc cover and then raise it. (2) Place a disc onto the disc spindle. Press on the center of a disc until it locks onto the disc spindle. (3) Close the disc cover. Caution: • Insert a disc firmly until it locks onto the spindle and then close the disc cover, or the disc may fall off the spindle and get damaged. Removing a disc (T) Make sure that the disc is not spinning. (2) Slide the OPEN lever to open the disc cover and then raise it. (3) Carefully remove the disc by lifting it. Press on the disc spindle, then lift the disc by holding its edge. Caution: • Close the application, if you are using the drive with your computer and make sure that the BUSY indicator (amber) is not blinking or lit before opening the disc cover. Reading from a CD Playing a CD-ROM To use a CD-ROM, refer to the manual or “README” file included on the CD-ROM. • Some types of CD-ROMs [game CD-ROM with audio track, CD Extra, Portfolio CD (Photo CD), etc.] allow you to listen to the sound or music through the headphones/external speaker system (not supplied) with the LINE OUT jack of the drive. Connect the headphones/external speaker system (not supplied) with the LINE OUT jack of the drive. If the LINE IN jack is available on the sound system of your computer, make a connection between the LINE IN jack of your computer and LINE OUT jack of the drive using an audio cable with 0 3.5 mm mini stereo plug at both ends. The cable can be obtained at mass electronics stores. Playing an audio CD You can operate an audio CD on your computer using an audio CD control software. Sound can be heard through the LINE OUT jack. • To listen to the sound or music of an audio CD, connect the headphones/ external speaker system (not supplied) with the LINE OUT jack of the drive. If the LINE IN jack is available on the sound system of your computer, make a connection between the LINE IN jack of your computer and LINE OUT jack of the drive using an audio cable with 0 3.5 mm mini stereo plug at both ends. The cable can be obtained at mass electronics stores. 24 Insertion / Removal of the USB Cable ■ Users for Windows 98 The supplied USB cable supports the Hot Swap function. With your computer turned on, you can insert/remove the USB cable without fear of hardware damage. Users for Windows2000 1. Double-click “Unplug / Eject” icon in task bar. “Unplug” or “Eject Hardware” window appears. 2. Click on the “Display device components”. 3. Select “USB Mass Storage Device” linked with “MATSHITA KME CD-ROM11 USB Device” and click [Stop]. 4. Click OK . Safe To Remove Hardware The USB Mass Storage Device1 device can now be safety removed from the system. on 5. Click [Ôjr. 6. Remove the USB cable. Maintenance Caution: • Do not use solvents such as benzine, thinner, alcohol, record cleaners or anti-static spray. I When the outside of the drive is dirty: I When a disc is dirty: I When the tens is dirty: 26 Troubleshooting If trouble occurs, check the following points before returning the drive for service. Trouble Possible Cause Solution Your computer does not recognize the drive, or does The Auto Protect function of AC adaptor is working. Disconnect the AC adaptor and connect it again after few minutes. not function properly. Your computer has not been setup yet. Set up your computer, (install the device drivers, if it is necessary.) (es- p. 17). The USB cable is not connected to the drive or to your computer properly. Properly connect the USB cable (i®- P. 20). The USB cable pin is bent or broken. Consult your dealer (or contact Panasonic Service Center at 1-800-PANA-SYS for users in continental United States). The drive is off. • Turn on the drive and restart your computer^ P. 22). • If you use the drive with the USB interface power, confirm the “Setting the Power Mode” (ca- P. 15). Operating System is not matched. The drive works only with Windows 98 / Windows 2000. (continued) Troubleshooting Trouble Possible Cause Solution Your computer does not recognize the drive, or does not function properly. Confirm the “Device Manager” to see if the drive has been installed correctly. How to view the Device Manager: 1. Right-click the “My Computer” icon at the desktop and then click the “Properties”. 2. Double-click the “Device Manager” tab. After installation, connect the USB cable to your computer and open the “Device Manager” window. You should have entries in the “Device Manager1’ similar to below. Computet CDROM MATSHITA KME CD-R0M11 SCSI controllers I : ^ KME CD-R0M11 USB Adapter l^ -jSj System devices :..... USBCD Bus Enumerator Universal serial bus con...