valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
-Check your antenna connections; make sure the antenna is properly grounded at its mounting location. • The antenna may not be the proper length. -Make sure the antenna is fully extended; if broken, replace the antenna with a new one. Broadcast is noisy. • The antenna is not the proper length. -Extend the antenna fully; replace it if it is broken. • The antenna is poorly grounded. -Make sure the antenna is grounded properly at its mounting location. CD CD Player/Changer not functioning. • Out of operating temperature range +50.C (+120.F) for CD. -Allow the vehicle's interior (or trunk) temperature to cool. CD playback sound is wavering. • Moisture condensation in the CD Module. -Allow enough time for the condensation to evaporate (about 1 hour). CD insertion not possible. • A CD is already in the CD player. -Eject the CD and remove it. • The CD is being improperly inserted. -Make sure the CD is being inserted following instructions in the CD Player Operation section. Unable to fast forward or backward the CD. • The CD has been damaged. -Eject the CD and discard it; using a damaged CD in your unit can cause damage to the mechanism. CD playback sound skips due to vibration. • Improper mounting of the unit. -Securely re-mount the unit. • The disc is very dirty. -Clean the disc. • The disc has scratches. -Change the disc. • The pick-up lens is dirty. -Do not use a commercial available lens cleaner disc. Consult your nearest ALPINE dealer. CD playback sound skips without vibration. • The disc is dirty or scratched. -Clean the disc; damaged disc should be replaced. Error displays (built-in CD player only) • Mechanical error -Press c. After the error indication disappears, insert the disc again. If the above-mentioned solution does not solve the problem, consult your nearest ALPINE dealer. CD-R/CD-RW playback not possible • Close session (finalization) has not been performed. -Perform finalization and attempt playback again. MP3/WMA MP3 or WMA is not played back. • Writing error occurred. The CD format is not compatible. -Make sure the CD has been written in a supported format. Refer to “About MP3/WMA” (page 11-12), then rewrite in the format supported by this device. 24-EN Indication for CD Player Indication for CD Changer HI TEMP • Protective circuit is activated due to high temperature. -The indicator will disappear when the temperature returns to within operation range. NO DISC • No CD is inserted. -Insert a CD. • Although a disc is inserted, “NO DISC” is displayed and the unit does not start to play or eject the disc. -Remove the disc by following these steps: 1) Press the c button. The movable display will open. 2) Press the c button again for at least 2 seconds while the movable display is open. ERROR • Mechanism error. 1) Press the c button and eject the CD. If not ejecting, consult your Alpine dealer. 2) When the error indication remains after ejecting, press the c button again. If the error indication still does not turn off after pressing the c button for a few times, consult your Alpine dealer. • When “ERROR” is displayed: If the disc cannot be ejected by pressing c, press the RESET switch (refer to page 6) and press c again. If the disc still cannot be ejected, consult your Alpine dealer. PROTECT • A copy-protected WMA file was played back. -You can only play back non-copy-protected files. UNSUPPORT • The disc is not written in a MP3/WMA supported format. -Use a disc written at the MP3/WMA supported format. HI TEMP • Protective circuit is activated due to high temperature. -The indicator will disappear when the temperature returns to within operation range. ERROR - 01 • Malfunction in the CD Changer. -Consult your Alpine dealer. Press the magazine eject button and pull out the magazine. Check the indication. Insert the magazine again. If the magazine cannot be pulled out, consult your Alpine dealer. • Magazine ejection not possible. -Press the magazine eject button. If the magazine does not eject, consult your Alpine dealer. ERROR - 02 • A disc is left inside the CD Changer. -Press the eject button to activate the eject function. When the CD Changer finishes the eject function, insert an empty CD magazine into the CD Changer to receive the disc left inside the CD Changer. NO MAGZN • No magazine is loaded into the CD Changer. -Insert a magazine. NO DISC • No indicated disc. -Choose another disc. 25-EN Indication for SAT Receiver Mode Indication for iPod Mode ANTENNA • The XM or SIRIUS antenna is not connected to the XM or SIRIUS radio module. -Check whether the XM or SIRIUS antenna cable is attached securely to the XM or SIRIUS radio module. UPDATING CALL 888-539SIRIUS TO SUBSCRIBE (XM mode) (SIRIUS mode) Scrolling display • Radio is being updated with latest encryption code. -Wait until encryption code is being updated. Channels 0 and 1 should function normally. NO SIGNAL ACQUIRING SIGNAL (XM mode) (SIRIUS mode) Scrolling display • XM or SIRIUS signal is too weak at the current location. -Wait until t...