valutazioni - 4, GPA: 5
(
)
)
|
Foto e specifiche Alpine CDM-7856R |
Facilità d'uso
Using such accessories can cause the disc to be out of standard specifications and may create operational problems. We recommend not using these accessories on discs played in Alpine CD players. Transparent Sheet Disc Stabilizer 3-EN Basic Operations POWER BAND 2 MODE / LOUD c g DN f UP Detaching the Front Panel 1 Press and hold the POWER button for at least 3 seconds to turn off the power. 2 Press the (Release) button at lower left corner until the front panel pops out. 3 Grasp the left side of the front panel and pull it out. NOTES • The front panel may become hot in normal usage (especially the connector terminals), this is not a malfunction. • To protect the front panel, place it in the supplied carrying case. Attaching the Front Panel 1 First, insert the right side of the front panel into the main unit. Align the groove on the front panel with the projection on the main unit. 2 Push the left side of the front panel until it locks firmly into the main unit. 211 NOTE Before attaching the front panel, make sure that there is no dirt or dust on the connector terminals and no foreign object between the front panel and the main unit. 1 SETUP • Controllable With Remote Control This unit can be controlled with an optional Alpine remote control. For details, consult your Alpine dealer. Point the optional remote control transmitter at the remote control sensor. Remote control sensor • Connectable to Remote Control Interface Box You can operate this unit from the vehicle's control unit when an Alpine Remote Control Interface Box (optional) is connected. For details, contact your Alpine dealer. Initial System Start-Up 1 Immediately after installing or applying power to the unit, it should be initialized. To do this, first, remove the detachable front panel. Behind the front panel, to the right of the connector, there is a small hole. Using a pencil or other pointed object, press the Reset switch mounted behind this hole to complete the initialization procedure. Reset switch 4-EN Turning Power On and Off 1 Press the POWER button to turn on the unit. NOTE The unit can be turned on by pressing any other button except the eject c button. The volume level gradually increases to the previous level you were listening to before the unit was turned off. Press and hold the POWER button again for at least 3 seconds. NOTE The very first time the power is turned on, the volume will start from level 12, and the LOUD function will be on in the tuner mode. Subwoofer On and Off 1 Press and hold the SETUP button for at least 3 seconds. 2 Press the g DN or f UP button to select the SUB-W mode. 3 Press the BAND button to select Subwoofer ON or OFF. 4 After setting is completed, press the SETUP button to return to normal mode. NOTES • Initial mode is "Subwoofer ON." • Set to "Subwoofer OFF" unless the subwoofer is used. • When the subwoofer is turned on, the subwoofer output level can be adjusted. For more details, refer to the Adjusting Volume/Balance/Fader. Adjusting Volume/Balance (Between Left and Right)/Fader (Between Front and Rear) 1 Press the MODE button repeatedly to choose the desired mode. Each press changes the modes as follows: > VOL > BAL > FAD NOTE If the 5 or 6 button is not pressed in 5 seconds after selecting the BALANCE and FADER modes, the unit automatically sets in the VOLUME mode. 2 Press the 5 and 6 buttons until the desired sound is obtained in each mode. Turning Loudness On/Off Loudness introduces a special low- and high- frequency emphasis at low listening levels. This compensates for the ear's decreased sensitivity to bass and treble sound. 1 Press and hold the LOUD button for at least 2 seconds to activate or deactivate the loudness mode. The display shows "LOUD ON" when the loudness mode is activated. Adjusting Source Signal Levels If the difference in volume level between the CD player and FM radio is too great, adjust the FM signal level as follows. 1 Press and hold the SETUP button for at least 3 seconds. 2 Press the g DN or f UP button to select the FM LV (FM LEVEL) mode. 3 Press the BAND button to select the FM signal level HI (High) or LO (Low) to make the signal levels between the FM band and CD player closer. 4 Press the SETUP button to return to normal mode. 5-EN Basic Operation SOURCE BAND 21 g DN f UP Setting the Bass Control You can change the Bass Frequency emphasis to create your own tonal preference. 1 Press the BASS C. button to turn on the Bass setting mode. 2-1 Setting the Bass frequency: Press the g DN or f UP button to select the desired Bass centre frequency. 60Hz - 80Hz - 100Hz - 200Hz Emphasizes the displayed Bass frequency ranges. 2-2 Setting the Bass Band Width (Q-Factor): Press the BAND button to select the desired Bass Band Width. > WIDE1 > WIDE2> WIDE3 > WIDE4 (Wide)< >(Narrow)........................... Changes the displayed frequency's band width to narrow or wide. 2-3 Setting the Bass Level: Press the 5 55555 or 6 66666 button to select the desired Bass Level (-7~+7). You can...
Questo manuale è adatto anche per i modelli :CD-giocatori - CDM-7859R (580.42 kb)
CD-giocatori - CDM-7858R (580.42 kb)