valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
OPEN/CLOSE BUTTON : Press the OPEN/CLOSE BUTTON (3) to load or remove a CD from the DISC TRAY (2). DISPLAY: The DISPLAY (4) shows the track numbers, play mode, pause mode, and 3 different time displays. These time displays are time elapsed on the track, time remaining on the disc and time remaining on the track. PLAY/PAUSE : Each press of the PLAY/PAUSE BUTTON (7) causes the operation to change from play to pause or from pause back to play. See the CUE INSTRUCTIONS section for more information. TRACK SKIP : The TRACK SKIP BUTTONS (6) let you select the track to play. SCAN BUTTONS : The SCAN BUTTONS (8) are used to move foward or reverse while in play mode. The SCAN BUTTONS (8) are also used to accurately position the disc at the point where you wish the track to start playing. This position on the track is memorized as the cue point. See the CUE INSTRUCTIONS section for more information. STOP : The STOP BUTTON (13) will end the playing of the CD. Also use the STOP BUTTON (13) to clear selections when programming. TIME: The TIME BUTTON (10) switches the time display between the three available choices listed under DISPLAY. CUE: With the unit in the play mode, and after memorizing the cue point, pressing the CUE BUTTON (5) will cause the CD player to enter the pause mode at the memorized cue point. Holding down the cue button changes the cue function to preview (allowing you to hear the music play from the cue point) and releasing the cue button returns you to the preset cue point. If a cue point is not memorized, pressing the CUE BUTTON (5) will cause the unit to return to the beginning of that track. CUE/B REPEAT: After the cue point is memorized, pressing the CUE/B BUTTON (12) in the play mode, repeats the section between the cue point and the point where the CUE/B BUTTON (12) was pressed (there will be a slight delay between the end and the restart of play). SINGLE-AUTO CUE/CONTINUOUS: Pressing the SINGLE-AUTO CUE/ CONTINUOUS (11) button activates the AUTO CUE FUNCTION. The AUTO CUE FUNCTION causes the unit to pause at the beginning of music of the following track and allows you to start play immediately from the start of music without any blank space (which exists at the beginning of every track). Pressing the SINGLE-AUTO CUE/ CONTINUOUS (11) button a second time activates the CONTINUOUS function causing the unit to play continuously (after the last track, the unit will return to the first track of the disc and continue to play). Pressing the SINGLE-AUTO CUE/CONTINUOUS (11) button a third time deactivates the CONTINUOUS function. PITCH CONTROL: Moving the PITCH CONTROL (14) activates the pitch control of the unit, and the pitch of the CD will change according to the position of the slide. PITCH BEND : Pushing the PITCH BEND BUTTONS (9) will temporarily raise or lower the pitch without changing the slide setting. Releasing the buttons will return the pitch to the slide setting. DIGITAL OUTPUT JACK: Connecting any type of DAT, MD, HARD DRIVE, or other such items which accept digital signals into the BNC CONNECTOR (15) on the rear panel of the transports allows you to receive a digital signal from CD. OPERATING INSTRUCTIONS 1. Make sure that the VOLTAGE SELECTOR SLIDE SWITCH (17), found on the rear panel, is set for the proper voltage. Plug the unit in and press the POWER SWITCH (1). The unit will turn on. Pushing the POWER SWITCH (1) a second time will turn the unit off. 2. Press the OPEN/CLOSE BUTTON (3), place a CD in the DISC TRAY (2) and press the OPEN/CLOSE BUTTON (3) again. The tray will close into the unit. The display will initially show the number of tracks and the total time of the CD. 3. Push the TRACK SKIP BUTTONS (6) to select the track you want to play. 4. Press the PLAY/PAUSE BUTTON (7) and the unit will instantly play. Page 3 CUE INSTRUCTIONS 1. To start the play at a point other than the beginning of a track, follow these instructions: First choose the track you wish to play, and then press the PLAY/ PAUSE BUTTON (7) so the unit goes into the play mode. Press the PLAY/PAUSE BUTTON (7) to pause play at the spot where you want the play to start the CUE POINT. Use the SCAN BUTTONS (8) to pick the precise spot you want play to begin, then press the PLAY/ PAUSE BUTTON (7) again to save the cue point. Press the CUE BUTTON (5) to pause play at the cue point (the unit will go into the pause mode and the location indicated on the display will be the memorized cue point). You can preview the cue point by pressing and holding down the CUE BUTTON (5). Press the PLAY/PAUSE BUTTON (7) to begin play from the cue point. 2. Once you have saved a cue point you can fine tune or change the memorized cue point: To change a cue point, push the PLAY/PAUSE BUTTON (7) so the unit plays from the cue point, then press the PLAY/PAUSE BUTTON (7) at the spot you wish your new cue point. Press the PLAY/PAUSE BUTTON (7) again to save the cue point. The unit will go into the pause mode and the location indicated on the di...