valutazioni - 4, GPA: 4.5
(
)
)
|
Facilità d'uso
According to the amplifier, set the EQ ON/OFF switch under the turntable platter. Audio cord .To AC outlet When the unit is connected to the PHONO (MM) jacks Rear panel of White the amplifier Audio cord \ I Î □ OFF E Q O N Red When the unit is connected to the AUX jacks, etc. : i □ OFF E Q O N [ AUX Rear panel of the amplifier r Caution: Do not apply oil or lubrication to the motor, tonearm, or any of the turntable’s mechanisms. I P-T400 (En) Installing the turntable belt Using the stylus cover □ Set the turntable platter carefully on the center snindle. m spindle. Using the ribbon tape, engage the drive belt with the motor pulley as shown. 0 Remove the ribbon tape. • Take care not to twist the drive belt. Replacing the stylus r -\ • Use an N-76 replacement stylus. • Remove this unit’s power cord from the AC outlet before replacing the stylus. • One stylus is good for playing an LP record approximately 500 times. El Remove the existing sty-lus in the order Stylus O'! Install the new stylus in ZA the order O—© y Operating instructions Placing a record on the platter. With an LP record With an EP (single) record 0 Select 33 or 45. When playing 33 rpm record. When playing 45 rpm record. 33 45 o FI Set the cueing lever to "I". • The arm elevator rises. □ Playing the record. (1) Pick up and move the to-nearm to the position where you wish to begin listening. Tonearm »The turntable platter begins rotating when the tonearm Is moved over the record. (2) Set the cueing lever to • The tonearm is lowered on the record surface and playback starts. • It may happen that tonearm returns automatically to the arm rest before play start. If this occurs, repeat steps (1) and (2) again. To pause record playback Set the cueing lever to " 1' r a • To resume playback, set the cueing lever to " z To stop record playback CUT 33 45 o o • The tonearm automatically returns to the arm rest when playback is finished. Before operation, remove the stylus cover in the direction of the arrow -N After record play, always put on the stylus cover to protect 8 I In case of difficulty P-T400 (En) What appears to be a malfunction may not always be serious. If your unit should not perform as expected, consult the table below to see if the problem can be corrected before seeking help from your dealer or service representative. Symptom Cause Remedy No sound from both left and right channels or one channel. • Turntable audio cable are not connected correctly. • Check connections to amplifier. Loud hum, no music. • Poor connection of turntable audio cables. • Make solid connections to amplifier. Howling drowns out music when volume is increased. • Speaker vibration picked up by turntable. • Separate turntable from speakers. Turntable platter does not turn. • Poor AC plug contact. • Turntable belt does not engage with the motor pulley. • Check connection. Make sure AC outlet is active. • Engage the turntable belt with the motor pulley. Poor tracking • Excessive dust on record or stylus. • Stylus tip wear. • Remove dust from stylus or record. • Replace the stylus. (Refer to “Replacing the stylus” on page 7.) Sound is too low or distorted. • The EQ ON/OFF switch under the turntable platter is not set correctly. • Set the switch correctly referring to “Connections”. Note: Do not use contact cleaner because it could cause a malfunction. Be specially careful against contact cleaners containing oil, for they may deform the plastic components. Specifications Motor and turntable Drive system................................................... Belt-drive system Motor.................................................................. DC servo motor Turntable platter............................................ 29.5 cm diameter Speeds....................................... 2 speeds; 33-1/3 and 45 rpm. Wow & flutter................................... Less than 0.05 % (WRMS) S/N (rumble)................................................. DIN : 65 dB (DIN B) Tonearm Type............................................... Integrated straight tonearm Effective arm length..................................... 215 mm (8-7/16") Cartridge Type................................................................................ MM type Stylus.............................................. N-76 with 0.6 mill diamond Frequency response........................................ 20 Hz to 20 kHz Output voltage............................. 2.5 mV (1kHz, 3.54 cm/sec.) Equalizer amplifier Output voltage (RIAA EQ ON). General Power consumption . Dimensions................ Weight (net) . 200 mV (1kHz, 3.54 cm/sec.) .......................... 4 W 400 mm (15-3/4") 103 mm (4-1/16") 380 mm (14-15/16") .......... 3.0 kg (6,6lb) Note: KENWOOD follows a policy of continuous advancements. For this reason specifications may be changed without notice. KENWOOD For your records Record the serial number, found on...