valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
Malfunction of microcomputer If operation is not possible or erroneous display appears even though all connections have been made properly, reset the microcomputer referring to “In case of difficulty”. . Make connections as shown below. When connecting the related system components, refer also to the instruction manuals of the related components. Caution regarding placement To maintain proper ventilation, be sure to leave a space around the unit (from the largest outer dimensions including projections) equal to, or greater than, shown below. Left and right panels: 10 cm Rear panel: 10 cm DIGITAL OUTPUT jack Commercially-available optical fiber cable SL 16/XS8 switch 8 System control cord Audio cord Amplifier Remove the protection cap when using the DIGITAL OUTPUT (OPTICAL) jack. To wall AC outlet To AC outlet A SL 16 XS-8 OUTPUT OPTICAL DIGITAL OUTPUT SYSTEM CONTROL L R SYSTEM CONTROL L R CD DIGITAL INPUT OPTICAL To AC outletMD recorder (DPF-3010/DPF-2010 only) NotesNotes 1. Connect all cords firmly. If connections are loose there could be loss of sound or noise produced. 2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging/unplugging connection cords without removal of the power cord can cause malfunctions or damage to the unit. DPF-3010/2010/1010 (En) Connection to a general-use amplifier Use the provided audio cords to connect the OUTPUT jacks of this unit to the CD input jacks (or AUX jacks) of the amplifier. Connection to digital amplifier or MD (only for DPF-3010/2010) Connect the DIGITAL OUTPUT (OPTICAL) jack to the digital input jack of the amplifier, DAT recorder, MD recorder, etc., using an optical fiber cable which are commercially available in audio stores. OWhen using an optical fiber cable to connect this unit to a digital amplifier, insert the plug straight into the jack until a snap sound is Optical fiber cable heard. OBe careful not to bend, coil, or bundle the optical fiber cable. OOptical fiber cables available on the market may not always be able to be used with this player. If your cord cannot be used with this unit, consult the store from which you purchased the cord or your nearest dealer. Adjusting the output levels of the output jacks and headphone output (only for DPF-3010/2010) The OUTPUT level (UP/DOWN) keys of the remote control unit can adjust the output levels from the LINE/OUT jacks and PHONES jack (DPF-3010 only) of the unit. REMOTE CONTROL UNIT RC-P0305 OUTPUT DOWN UP To use the headphone (only for DPF-3010) Connect a stereo headphone to the PHONES jack of the CD player. Adjust the sound volume using the remote control unit. SINGLE TIME _12 db Output level OIt is not favorable for the sound quality to decrease the output level from this unit too much. Use these keys for coordination with other line levels. OAdjusting the headphone output level also changes the LINE/OUT level. Do not adjust the output level from this unit particularly during recording. OPlease note that the sound output is at the maximum level when the power is turned on. DPF-3010/2010/1010 (En) SYSTEM CONTROL CONNECTIONS Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations. There are two KENWOOD system control modes. Make connec- tions according to the groups of terminal symbols shown below. [XS8] Mode : lets you combine F, f, and A terminals [SL16] Mode : for terminals only This unit is compatible with both [XS8] and [SL16] modes. O When all units in system control connection are set to [XS8] mode, set the SYSREM CONTROL selector switch on the rear to the [XS8] side and connect. O When all units in system control connection are set to [SL16] mode, set the SYSREM CONTROL selector switch on the rear to the [SL16] side and connect. ODo this operation after completing all connections. (Ensure that the unit is set to STANDBY mode.) 1. [SL16] equipment cannot be combined with [XR], [XS], and [XS8] equipment for system operations. If your equipment consists of this kind of combination, please do not connect any system control cords. Even without system control cords, normal operations can be car- ried out without affecting performance. 2. If your amp or receiver does not have a system control terminal, do not connect any system control cords to the system control terminals on the other components. 3. Do not connect system control cords to any components other than those specified by Kenwood. It may cause a malfunction and damage your equipment. 4. Be sure the system control plugs are inserted all the way in to the system control terminals. SYSTEM CONTROL SYSTEM CONTROL SYSTEM CONTROL SYSTEM CONTROL SYSTEM CONTROL SL16 XS 8 j SYSREM CONTROL selector switch NotesNotes SYSTEM CONTROL OPERATIONS Remote Control Lets you operate this unit with the system remote control unit supplied with the amplifier or receiver. Automatic Operation (Except [XR] equipment) Automa...
Questo manuale è adatto anche per i modelli :CD-giocatori - DPF-1010 (620.98 kb)
CD-giocatori - DPF-3010 (620.98 kb)