valutazioni - 0, GPA: 0
(
)
)
|
Facilità d'uso
Batteries (not included) Open the battery compartment and insert six batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity as indicated by the "+" and "–" symbols inside the compartment. Batteries contain chemical substances, so they should be disposed of properly. Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. Therefore: • Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. • When inserting new batteries, do not try to mix old batteries with the new ones. • Remove the batteries if the set is not to be used for a long time. Using AC Power 1 Check if the mains voltage, as shown on the type plate located on the bottom of the set, corresponds to your local mains supply. If it does not, consult your dealer or service centre. 2 Connect the mains lead to the AC MAINS inlet and the wall socket. The power supply is now connected and ready for use. 3 To switch off completely, unplug the mains lead from the wall socket. • Unplug the mains lead from the wall socket to protect your set during heavy thunderstorms. The typeplate is located on the bottom of the set Switching power on/off: Save energy Whether you are using mains or battery supply, to avoid unnecessary energy consumption always adjust the source selector to off. General operation 1 To select your sound source adjust the source selector to CD/TUNER/OFF. 2 Adjust the sound with the VOLUME and DBB (Dynamic Bass Boost) controls. 3 To switch off the set, adjust the source selector to off position. Note: When the set is switched off the tuner presets will be retained in the set’s memory. Tuner Radio reception 1 Adjust the source selector to TUNER. ™ Display: shows tu briefly (See 2). 2 Press FM•MW once or more to select the desired waveband. ™ Display: shows your waveband and the preset number and the frequency of a preset station if already programmed (See 3) 3 Press and hold down .or §briefly to tune to a radio station. Release when the frequency in the display starts to change. ™ The radio automatically tunes to a radio station of sufficient reception. Display shows Srch during automatic tuning. (See 4) – For FM, pull out the telescopic aerial. Incline and turn the aerial. Reduce its length if the signal is too strong (very close to a transmitter). – For MW (AM) the set is provided with a built-in aerial so the telescopic aerial is not needed. Direct the aerial by turning the whole set. Programming radio stations You can store up to a total of 32 radio stations in the memory: 20 FM and 12 MW(AM). 1 Tune to your desired station (see Radio Reception). 2 Press PROG MODE to activate programming. ™ Display: prog flashes. (See 5) 3 Press PRESET + or – once or more to allocate a number from 1 to 20 for FM or 1 to 12 for MW(AM). 4 Press PROG MODE again to confirm the setting. ™ Display: prog disappears, the preset number and the frequency of the preset station are shown. (See 3) 5 Repeat steps 1-4 to store other stations. • You can erase a preset station by storing another frequency in its place. CD Player Display indication for CD functions – CD open: CD door open (See 6) – disc: CD inserted (See 7) – In stop mode: total track number and total playback time – During CD playback: elapsed playback time of current track and current track number – Pause: elapsed playback time freezes and flashes (See 8) – shuffle/ repeat modes: when the respective mode is activated – prog: when CD programme active); prog also appears briefly when you store a track (See 9) – no sel: programme activated but no tracks selected (See 0) – full: programme memory full (See !) – no prog: programme cancelled (See @) – no disc: no disc/ error in CD operation /CD-R(W) is blank or the disc is not finalized (See #+ Troubleshooting) Playing a CD This CD-player can play Audio Discs and CDRecordables. Do not try to play CD-Rewritables, a CD-ROM, CDi, VCD, DVD or computer CD. 1 Adjust the source selector to CD. ™ Display: shows Cd briefly. 2 To open the CD door, lift the CD door at the edge marked LIFT TO OPEN. 3 Insert a CD or CD-R with the printed side facing up and press the CD door gently close. 4 Press 2; on the set to start playback. 5 To pause playback press 2;. To resume, press 2; again. 6 To stop CD playback, press STOP 9. Note: CD play will also stop when: – you open the CD compartment; – you select TUNER sound source; – the CD has reached to the end. Selecting a different track During playback you can use . or §to select a particular track. • If you have selected a track number in the stop or pause position, press 2; to start playback. • Press §once briefly for the next track, or press repeatedly until the desired track number appears in the display. • Press .once briefly to return to the beginning of a current track. • Press .more than once briefly for a previous track. Finding a passage within a track 1 Press and hold down .or §. ...