valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
*4) Maximum output current at low level: 64 mA. (NOTE 1): Make sure the power consumption of the external device supplied by this pin is 200 mA or less. 28 2 Parallel remote wiring diagram 2 Parallel remote wiring diagram 9 1 9 2 9 3 9 4 9 5 9 6 9 7 9 8 9 10 9 11 9 12 15 13 15 14 8 7 6 5 4 3 2 1 131415 12 11 10 9 search 1/6search 2/7search 3/8search 4/9search 5/10selectshiftplaystop9 / repeat 8 / singleAUX1AUX2 29 ENGLISH ENGLISH With the DN-V1700, programs can be played at will using files that include unique script commands. . These operating instructions only include a general description of the script commands. For details of the individual commands, consult your store of purchase. 2 Script file names Script file names have the following format: File name with a maximum of 8 ASCII code characters + “.DSC”. Files are stored in the “SCRIPT” directory. 2 Executing script files Programmed playback using script files is performed by playing the desired script file in the “SCRIPT” directory. 2 Operation of the DN-V1700 while playing script files The commands included in the script file are executed in order. Execution of the following command begins once execution of the previous command is completed. When a file is playing, the next command is only executed after playback of the file finishes. If interrupt commands have been specified, execution shifts to the specified label according to the specified conditions, and the command in the next line in the label is executed immediately. When interruption under the same conditions is declared on multiple channels, the setting for the channel with the lowest number is effective. If “@” is added before a command, that command is executed even if a file is playing, after which the next command is executed immediately, without waiting for file playback to finish. (Refer to the list of script commands for the commands for which “@” is usable.) 2 Automatic script execution If there is a file with the name “ply00000.dsc” in the SCRIPT directory, the script is executed automatically when the device is started. (The script is not executed if the STOP button is held in while the device is starting.) 2 Stopping script playback Script playback can be stopped while a script is playing using the operations below, except when the “on break goto” command is set: • By pressing and holding the STOP button on the front panel for at least 2 seconds • By pressing and holding the parallel remote controller’s STOP button for at least 2 seconds • With the “RJ” serial remote command • With the “RJ” FTP “SITE” command During script playback, no operations other than the above stop operations and status confirmation by serial remote or “SITE” command are effective. 2 Script file format • TEXT file • The terminator of each command must be the return command of regular MS DOS files (0x0D0A). • Commands must be written either all in capital letters or all in small letters. An error will occur if a command contains both capital and small letters. Parameters and comments, however, may include both capital and small letters. • Comments may start from any position, as long as they start before the 79th character in a line. • The maximum number of characters per line is 78 (not including return) for lines that do not include comments, 250 for lines including comments. Even when the comment starts after the command, the “;” mark indicating the beginning of the comment must be placed within the first 78 characters. • The maximum number of lines per file (the total for command lines and label lines) is 250 (not including lines consisting only of comments). • The maximum file size, including comments, is 16 kilobytes (16,384 bytes). • When a parameter follows a command, separate it with a space. • When there are multiple parameters, separate them with commas. • When omitting parameters that can be omitted, the comma separating parameters cannot be omitted. When omitting the very last parameter, however, the comma preceding that parameter may be omitted. 30 ENGLISH ENGLISH • Label lines may consist of any character strings of up to 8 characters beginning with a sharp (“#”) (maximum 9 characters including the “#”). • The sharp is omitted when specified as such parameters as “GOTO”, “ONKEYGO”, or “ONBREAK”. • The characters that can be used in label names are capital letters “A to Z”, small letters “a to z” and numbers “0 to 9”. 2 Parallel remote terminal During script playback, parallel remote terminal pins 1 to 6, 11 and 12 function as keys 1 to 8, and can be used with the script command “ONKEYGO”, for example. 2 List of script commands (“n” refers to an integer) Command @ Format Description 1 comment ; Comment 2 play PLAY Playback of 1 or 2 files. The script does not move to the next step unless the file is played to the file end 3 play standby PLAYRDY Preparation for file playback 4 play start PLAYGO Start playback of file for which the play standby mode is set from the specified TC 5 end END End/cha...