valutazioni - 2, GPA: 5
(
)
)
|
Facilità d'uso
P 7 8 9 0 4 5 6 • 1 2 3 = ABCD 7 8 9 0 4 5 6 • 1 2 3 = A • After you perform an operation in any mode, pressing C returns to the Timekeeping Mode. • An input tone sounds each time you press a button. You can switch the confirmation tone on and off in the Calculator Mode. Alarm Mode 7 8 9 0 4 5 6 • 1 2 3 = Stopwatch Mode P 7 8 9 0 4 5 6 • 1 2 3 = 7 8 9 0 4 5 6 • 1 2 3 = Timekeeping Mode AB General Guide • You can use the Remote Control functions while in the Timekeeping Mode. • Press C to change from mode to mode. Each mode is explained in detail on the following pages. Calculator Mode CDTimekeeping Mode In addition to normal timekeeping, the Timekeeping Mode also provides you with remote control capabilities for your TV, video tape deck, and other devices equipped with a remote control unit. • This watch only controls devices equipped with a remote control unit. • For details on how to set the time and date, see “To set the time and date”. Note The explanations in this manual use button symbols (K, L, ), button markings ( 1 , 2 , etc.), and letters (A, B, etc.) to indicate buttons on the watch. Example: Press D to switch on the television. P 7 8 9 0 4 5 6 • 1 2 3 = ABCDSignal Emitter P ABCP TVJPress B. About the Timekeeping sub-modes The Timekeeping Mode is made up of four sub-modes. Use the B button while in the Timekeeping Mode to switch between the sub-modes. • If you leave the watch in the TV, Video or Learning Mode without performing an operation for about two or three hours, the watch automatically returns to the Normal Timekeeping Mode. • To manually return to the Normal Timekeeping Mode, press C to change to the Calculator Mode. Next, use C to change to the Timekeeping Mode. P LNormal Timekeeping Mode Video Mode (for video tape deck remote control) TV Mode (for television remote control) JP LEARNJLearning Mode (for remote control of other devices) About the TV and Video Tape Deck remote control function In order to be able to use this watch for remote control of a television or video tape deck, you must first set the appropriate manufacturer code. The manufacturer code tells the watch what signals to use for remote control. The Manufacturer Code Table shows the names of the manufacturers that correspond to each code. For full details on how to actually set the manufacturer code, see “To set the manufacturer code”. Some TV or tape deck models may not work properly with this watch, even though they are made by one of the manufacturers in the Manufacturer Code Table. Also, you may find that you can control a TV or tape deck using a code for a manufacturer that is different from the ones in the table. For details on finding the code you should use, see “How to find the right code”. Notes • Replacing the battery will cause the remote control data setting (TV/video manufacturer codes) to be altered. Be sure that you make a note of your codes before you have the battery replaced. • There are some manufacturers with more than one code. Try the various codes available for your equipment to find the one that works best. • You have to set separate codes for your TV and tape deck, even if they are made by the same manufacturer. • You might not be able to use this watch to control models that combine a TV and tape deck into a single unit, multi-functional TVs that can be used as computer monitors, or other televisions or tape decks equipped with special functions. Manufacturer code (TV) Manufacturer FERGUSON FUNAI GOLDSTAR GRUNDIG HITACHI JVC MITSUBISHI NEC PANASONIC Manufacturer PHILIPS PIONEER SAMSUNG SANYO SHARP SONY TELEFUNKEN TOSHIBA Code 17, 18 15, 16, 41, 42 06, 12, 13, 29, 32 20, 21, 22 03, 25, 26, 27, 28, 29 03, 04, 05, 30 03, 19 03, 29, 31, 32 02, 08, 09, 10 Code 06, 28 33 06, 12, 14, 15, 29, 32 03, 35, 36, 40 01, 03, 37 03, 07 23, 24 03, 38, 39, 40 Manufacturer AKAI FERGUSON FUNAI GOLDSTAR GRUNDIG HITACHI JVC MITSUBISHI NEC NOKIA Code 24, 25, 33 17, 18 15 26 20, 21, 22 04, 27, 42 03, 04, 05 06, 19 28, 29 30 Manufacturer code (video tape deck) Manufacturer PANASONIC PHILIPS PIONEER SAMSUNG SANYO SHARP SONY TELEFUNKEN TOSHIBA Code 02, 14 07, 08, 09, 10 31 16, 32, 33 34, 35, 36, 37, 38 01 11, 12, 13 06, 23 39, 40, 41 SET TV TV Mode indicator To set the manufacturer code 1. Switch on the TV or video tape deck whose manufacturer code you want to set. 2. In the Timekeeping Mode, press B to select the TV Mode ( TV ) or Video Mode ( ). • Select TV Mode if you want to set the code for your TV, or the Video Mode to set the code for your video deck. 3. Hold down A until a manufacturer code appears flashing on the display. BACSignal Emitter DManufacturer code 4. While the TV or video manufacturer code setting display is shown, press K to increase the code number. • Holding down K increases the code number at high speed. • See the Manufacturer Code Table for details on manufacturer codes. 5. To test whether or not the displayed manufacturer code is correct for your equipment, point the Signal Emitter (red wind...