valutazioni - 5, GPA: 4
(
)
)
|
Facilità d'uso
To prevent serious injury or death: • Fall Hazard - It is dangerous to use this product on an elevated surface, since child’s movement may cause the product to slide or tip over. Use only on a floor. • Suffocation Hazard - Never use on a soft surface (bed, sofa, cushion) since the product can tip over and cause suffoca- tion in soft surfaces. • Never leave child unattended. • Never use as a carrier or lift while child is seated. Never use the toy bar as a handle. • Use the upright position only when child has developed enough upper body control to sit without leaning forward. • Always use the restraint system until child is able to climb in and out of the product unassisted. • Reclined position not recommended for children who cannot sit up by them- selves (6 months approximately, until 9 Kg/20 lbs). WARNING 2 Consumer Information CAUTION This package contains small parts in its unassembled state. Adult assembly is required. • Please read these instructions before assembly and use of this product. • Adult assembly is required.Tool needed for assembly: Phillips screw- driver (not included). • Requires one “D” (LR20) alkaline battery (not included) for soother operation.Toy includes one non-replaceable button cell battery. • Product features and decorations may vary from photographs. Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Pad with Seat Back Tube Hint: Please refer to the care section to remove the seat back tube for cleaning. Toy (Toy may be different) Toy Bar Front Bar 2 Side Rails Crossbar Note: Tighten or loosen the screws with a Phillips screwdriver. Do not over-tighten the screws. Shown Actual Size #4 x 20 mm Screws – 6 To prevent serious injury or death: • Fall Hazard - It is dangerous to use this product on an elevated surface, since child’s movement may cause the product to slide or tip over. Use only on a floor. • Suffocation Hazard - Never use on a soft surface (bed, sofa, cushion) since the product can tip over and cause suffoca- tion in soft surfaces. • Never leave child unattended. • Never use as a carrier or lift while child is seated. Never use the toy bar as a handle. • Use the upright position only when child has developed enough upper body control to sit without leaning forward. • Always use the restraint system until child is able to climb in and out of the product unassisted. • Reclined position not recommended for children who cannot sit up by them- selves (6 months approximately, until 9 Kg/20 lbs). WARNING 2 Consumer Information CAUTION This package contains small parts in its unassembled state. Adult assembly is required. • Please read these instructions before assembly and use of this product. • Adult assembly is required.Tool needed for assembly: Phillips screw- driver (not included). • Requires one “D” (LR20) alkaline battery (not included) for soother operation.Toy includes one non-replaceable button cell battery. • Product features and decorations may vary from photographs. Parts IMPORTANT! Please remove all parts from the package and identify them before assembly. Pad with Seat Back Tube Hint: Please refer to the care section to remove the seat back tube for cleaning. Toy (Toy may be different) Toy Bar Front Bar 2 Side Rails Crossbar Note: Tighten or loosen the screws with a Phillips screwdriver. Do not over-tighten the screws. Shown Actual Size #4 x 20 mm Screws – 6 3 2 • First lift the front rails and then push out the back rails. Assembly • Place the side rails on a flat surface. • Fit the crossbar tabs into the small rectangular opening in each side rail. Push the crossbar down completely. • Insert two #4 x 20 mm screws into the crossbar and tighten. • Insert and "snap" the back rails into the sockets in the side rails. Pull up on the back rails to be sure they are secure. IMPORTANT! Before assembly and each use, inspect this product for damaged hardware, loose joints, missing parts or sharp edges. DO NOT use if any parts are missing or broken. Contact Mattel for replacement parts and instructions if needed. Never substitute parts. 1 Side Rails Crossbar LIFT 3 PUSH LIFT PUSH 4 Side Rails Front Bar Hint: You may want to install batteries into the soother before assembling the front bar to the front rails. • Position the front bar so that the soother is upright. Fit it to grooved area on the inside of the front rails. • Insert four #4 x 20 mm screws into the front rails and tighten. Hint: You may need the help of another adult to hold the front bar in place while you insert and fasten the screws. 4 Assembly • Insert the ends of the seat back tube (inside the pad) into the sockets in the front rail. Push down on the seat back tube until you hear a “click” on each side. • Pull up on the seat back tube to be sure it is secure. 5 Pad Seat Back Tube Socket Socket • Locate the pocket in the bottom of the pad. • Fit the hardboard (attached to the front bar) into the pocket in the pad. 6 Pocket Hardboard • Fit the clips on the front...