valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
• Align the raised dot on the tray with the raised dot on the frame. • Fit the hubs into the round wells in the frames. 8 Tray Round Wells Hold Hubs Hold Hubs Raised Dot Raised Dot Bottom View Side View Raised Dot Side View Raised Dot Hub Hub ASSEMBLY 6 9 OFF SP LP OFF LP SP 11 10 • Slide a retainer between the two ribs on one side of the tray, as shown. • Fit an M5 lock nut (protruding side facing away from the retainer) into the hexagonal hole in the retainer. • Fit a 5/16" washer onto the M5 bolt. Insert the M5 bolt through the frame, hub, tray and into the retainer. Tighten the bolt with a Phillips screwdriver. Do not over-tighten. • Repeat this procedure to fasten the other side of the tray to the other frame. Retainer Rib Rib Tray M5 x 39/16" Bolt M5 Lock Nut • Position the head with the face upright. • Insert and snap the tab on the head into the slot in the tray. • Insert two 5/8" screws with washer heads through the front holes in the tray and into the head. Tighten the screws with a Phillips screwdriver. Do not over-tighten. • Insert two 5/8" screws with washer heads through the back holes in the tray and into the head. Tighten the screws with a Phillips screwdriver. Do not over-tighten. Head Slot Tab Tray Protruding Side Frame M5 Lock Nut ASSEMBLY 5/16" Washer •While pressing the upper buttons on both sides of the base, rotate the tray down until it "snaps" into position. Make sure you hear a "snap". IMPORTANT! If the tray does not “snap” into position, you have assembled the tray to the frame backwards. Remove the M5 bolt, retainer and M5 lock nut from the frame and tray. Carefully lift the tray from the round wells in the frame. Re-read and repeat Assembly steps 7-9. OFF LP SP 12 Upper Buttons • Position the seat ring so that the inside (ribbed side) is up and the marking is toward you. • Position the pad so that the Fisher-Price® logo is facing you (although it will be upside down!) • Fit the red slots on the pad (next to the Fisher-Price® logo) to the seat ring pegs on either side of the marking, as shown. 13 Seat Ring Ribbed Side Marking Fisher-Price® Logo Pegs Red Slot Red Slot Pegs Tray 7 Press Upper Button Press Upper Button • Pull the pad through the seat ring and wrap the pad around the outside of the seat ring. 14 Pad Pad Seat Ring Seat Ring Marking Top View ASSEMBLY ASSEMBLY • Fit the other six slots in the seat pad to the corresponding pegs on the seat ring. • Tuck the seat pad behind all four rollers. 15 Peg 3 Peg 5 Peg 6 Peg 1 Peg 2 Roller Peg 4 Roller RollerRoller RollerRoller Roller Roller 16 Seat Tray Push Seat Lock In • Push the seat lock to the unlocked position. • Insert and "snap" the seat into the hole in the tray. IMPORTANT! Assembly is now complete, but you will still need to properly setup this product for use. Please refer to the Battery Installation section and the Operation and Use section, beginning with step 3 for additional instructions. 8 BATTERY INSTALLATION • Face the front of the product • While pressing the tray release button (lower button) on each side of the base, rotate the tray up. 1 Tray Tray Release Button Tray Release Button Press Lower Button Press Lower Button • Locate the battery compartment on the bottom of the tray. • Loosen the screw in the battery compartment door with a Phillips screwdriver. • Remove the battery compartment door. OFF SPLP 2 Battery Compartment Bottom View 9 BATTERY INSTALLATION • Face the front of the product • While pressing the tray release buttons (upper buttons) on both sides of the base, rotate the tray down until it "snaps" into 4 Upper Buttons Tray Press Upper Button Press Upper Button Battery Compartment Battery Compartment Door SHOWN ACTUAL SIZE 1.5 x 3 "AA" (LR6)3 position. Make sure you hear a "snap". • Insert three "AA" (LR6) alkaline batteries as shown inside the battery compartment. Hint: Use only alkaline batteries for longest battery life. • Replace the battery compartment door and tighten the screw with a Phillips screwdriver. Do not over-tighten. Battery Tips • Do not mix old and new batteries. • Do not mix different types of batteries: alkaline, standard (carbonzinc) or rechargeable (nickel-cadmium). • Remove the batteries during long periods of non-use. Always remove exhausted batteries from the product. Battery leakage and corrosion can damage this product. Dispose of batteries safely. • Never short circuit the battery terminals. • Non-rechargeable batteries are not to be recharged. • Only batteries of the same or equivalent type as recommended in the Battery Installation instructions are to be used. • If removable rechargeable batteries are used, they are only to be charged under adult supervision. • Rechargeable batteries are to be removed from the toy before they are charged. • If you use a battery charger, it should be examined regularly for damage to the cord, plug, enclosure and other parts. Do not use a damaged battery charger until it has been properly repaired. IMPORTANT! If sounds and/or lights be...