valutazioni - , GPA:
(
)
)
Produttore : Polycom
File Size : 3.14 mb
File Nome : v2iu_4350_user_guide_7_2_2.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
The T1 port should not be connected to the telco network. •Fully integrated CSU/DSU •T1 support •Fractional T1 support •Layer 2 protocol support for: HDLC, Cisco HDLC (cHDLC), PPP, MLPPP, MLPPPoFR, Frame Relay •On-board RJ-48 connector for easy direct connection •T1/E1 framer and transceiver —B8ZS/HDB3 zero suppression —Response to Inband Loop codes (ANSI) —Manual payload loop through the GUI •External transmit clock input and receive clock output headers •Timing: internal or external (loop times from the network) •Provides long haul CSU or short haul DSU signaling •Meets FCC part 68 protection requirements Security VoIP Quality of Service Call Quality Monitoring Future-proof Scalability Feature Summary •VoIP —SIP, MGCP (for voice) and H.323 (for video) application layer gateway enables a single public IP address to be used for multiple VoIP endpoints •QoS —Class based queuing/prioritization —Diffserv marking and policing —Traffic shaping —VoIP call admission control prevents oversubscription of priority queue •Security —Stateful packet inspection firewall —VoIP aware firewall dynamically provisions and closes UDP ports used for VoIP calls —IPSec: 3DES, SHA-1 —NAT/PAT server hides enterprise LAN topology •Passive Call Quality Monitoring —Per call statistics include mean opinion score (average and minimum), jitter, latency, packet loss and much more —Alarms for poor MOS scores —Active call count indicators Front Panel LEDs LED Label Activity Description A Power Off Power switch is off (or no power from the AC outlet) Green Power is supplied to the unit B Status Off The unit could not boot up because of self test failure Green Self test passed Flashing Green Configuration is being written to permanent storage or an upgrade is in progress C T1 Off The T1 is in an alarm state and not synchronized Green T1 is in sync and no alarms are reported Back Panel 2 Getting Started Physical Installation •Never assume that the AC cord is disconnected from a power source. Always check first. •Always connect the AC power cord to a properly grounded AC outlet to avoid damage to the system or injury. Warning Secure the power supply using a fastener or nearby shelf so that it does not hang from the power connector. Required Tools and Materials •If the unit is to be mounted on the wall: —1 Flat or Phillips screw driver —2 round or flat head Phillips or slotted screws - 1 . inch long —2 hollow wall anchors •If the unit will be mounted in a shelf: —1 Flat or Phillips screw driver •If the T1/E1 port will be used to connect to WAN: —T1 cable to connect the T1/E1 port to a T1 line. Warning To reduce the risk of fire, use only 26 AWG or larger wire (e.g. 24, 22, 20, etc.) to connect the T1 port on your unit to an RJ-45 jack. •Ethernet cables to connect the LAN ports to LAN switches or to individual IP phones. They can also be used to connect the Ethernet WAN port to a WAN router, a Cable Modem or a DSL Modem, if T1/E1 port is not being used to connect to the WAN. Desktop Installation 1.Remove the 4350 and accessories from the shipping container. 2.Place the 4350 on a flat, dry surface such as a desktop, shelf or tray. 3.Connect the power and network cables to the appropriate ports on the back of the system. Caution To reduce the risk of fire, use only 26 AWG or larger wire (e.g. 24, 22, 20, etc.) to connect the T1 port on your unit to an RJ-45 jack. Wall-Mount Installation 2.Install two screws 5.9" (150 mm) horizontally apart on a wall or other vertical surface. The screws should protrude from the wall so that you can fit the appliance between the head of the screw and the wall. If you install the screws in drywall, use hollow wall anchors to ensure that the unit does not pull from the wall due to prolonged strain from the cable and power connectors. 3.Remove the 4350 and accessories from the shipping container. 4.Mount the 4350 on the wall as shown below. 1.Connect the power and network cables to the appropriate ports on the back of the system. Warning Secure the power supply using a fastener or nearby shelf so that it does not hang from the power connector. Caution To reduce the risk of fire, use only 26 AWG or larger wire (e.g. 24, 22, 20, etc.) to connect the T1 port on your unit to an RJ-45 jack. Rack-Mount Installation 1.Attach the ear mounts to both sides of 4350 with the screws. 2.Attach the 4350 with the ear mounts to the shelf by screwing the ear mounts to the shelf with screws. Connecting the Power and Cables Warning Always connect the AC power cord to an AC outlet suitable for the power supply that came with the unit in order to reduce the risk of damage to it. •Connect one end of the AC power cord to the power adapter and the other one to the AC outlet. •Connect plug from the power adapter to the Power Connector on the 4350. Sometimes a little force is necessary to get the plug properly positioned Caution Secure the power adapter using a fastener or tie wrap to nearby shelf so that it does not hang from the power connecto...