valutazioni - 1, GPA: 5
(
)
)
|
Facilità d'uso
35 19. 20. Install spacers (51) onto backboard brackets (52), with bolts (53, 54) and lock nuts (55, 37) as shown. 53 51 37 52 55 54 IMPORTANT!: KEEP HARDWARE LOOSE UNTIL AFTER STEP 25 IS COMPLETED. P/N 211574 09/04 18 58 59 57 56 56 59 68 58 59 57 56 56 59 68 56Lower Elevator tube Toward Pole 52 21. Toward Board Identify elevator tubes (63 & 56). Toward 63 Toward Board Pole Upper Elevator tube Attach lower elevator tubes (56) and counter balance spring (68) to backboard support brackets (52) using spacers (59), bolt (57), and nut (58) as shown. 19 09/04 P/N 211574 P/N 211574 09/04 20 22. 52 15 15 60 70 62 68 23. 58 63 63 57 59 52 59 Starting with nuts (15) flush against bracket (52) secure rim (70) and bracket to backboard. IMPORTANT! For spring loaded rim assembly, refer to instructions included with rim hardware. NOTE: Rim mounting nuts and bolts supplied with rim hardware. NOTE: DO NOT use washers here on spring return style rims. Attach upper elevator tubes (63) to backboard support brackets (52) using spacers (59), bolt (57), and nut (58) as shown. 58 58 65 64 56 1 66 66 57 67 56 67 24. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as shown. Install pole cap (64). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. 58 58 65 64 56 1 66 66 57 67 56 67 24. Support pole on sawhorse. Attach backboard assembly to top pole section (1) as shown. Install pole cap (64). NOTE: Two people are recommended for this step. Use caution; elevator assembly is heavy. 25. Install upper elevator tubes (63) to triangle plates (66) as shown. Install handle assembly to lower elevator tubes (56) using bolt (57), spacers (67), and nut (58) as shown. NOTE: Before going on to next step, set adjustable system assembly to the 10’ (3.05 m) setting. 09/04 P/N 21157421 57 63 67 58 1 58 63 67 66 51 57 56 56 67 67 TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. WARNING! IMPORTANT!: TIGHTEN ALL HARDWARE FROM STEP 20-25 AFTER THIS ASSEMBLY IS COMPLETED. 26. Insert bolt (57) through left side upper elevator tube (63), then stretch spring (68) onto bolt (57). Insert bolt (57) through right side upper elevator tube (63) and secure with nut (58). WARNING! USE EYE PROTECTION WHEN INSTALLING SPRINGS. 57 63 58 68 63 P/N 211574 09/04 22 SECTION D: INSTALL FRONT COVER & HANDLE Upright system and fill base (8) with water (approx. 40 gallons) and snap fill cap (42) in place. 27. 42 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 8 WARNING! DO NOT LEAVE ASSEMBLY UNATTENDED WHEN EMPTY; IT MAY TIP OVER. CAUTION! ADD TWO GALLONS (7.6 LITERS) OF NON-TOXIC ANTIFREEZE IN SUBFREEZING CLIMATES. NOTE: 44 IF USING SAND: 2 GALLONS OF ANTI-FREEZE IS NOT REQUIRED Attach front cover (40) to hinge tubes (18) using carriage bolts (51) and flange nuts (22) 28. as shown. 24 15 40 61 23 09/04 P/N 211574 P/N 211574 09/04 24 29. Roll assembly to desired playing area. Secure assembly to ground using strap (44) and tie down stake (7). 44 7 30. 8 ELEVATOR HEIGHT ADJUSTMENT 35 A. B. C. 31 DO NOT ALLOW CHILDREN TO ADJUST HEIGHT. WARNING! 31. A. While holding handle, remove pin (35). B. Move elevator up or down to desired height. C. Replace pin (35) full length to lock system at desired height. Apply height and moving label (43) to front of pole as shown. 2 2 1 3 203814 03/04 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 2. Rotate handle forward until wheels engage ground. 3. Move basketball system to desired location. 4. Rotate handle back to original position. 5. Reattach ground restraint and check system for stability. HEIGHT ADJUSTMENT 1 3 2 4 TO ADJUST BACKBOARD: 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 3. Replace pin full length to lock system at desired height. 10 feet (3.05m) 43 of net clips, or when all net clips are not present could result in bodily harm. Be sure to follow directions carefully. AVERTISSEMENT : L'utilisation de ce produit sans installer correctement ou toutes les pinces du filet risque de causer des blessures. Veillez a suivre scrupuleusement les instructions. WARNUNG: Ein Gebrauch dieses Produkts ohne ordnungsgema. angebrachte Netzhalteklammern bzw. ohne den Gebrauch der Netzhalteklammern kann Verletzungen nach sich ziehen. Die Anleitung genau befolgen. ADVERTENCIA: Si este producto se usa con los sujetadores de la red incorrectamente instalados, o si no estan todos presentes, se pueden ocasionar lesiones corporales. Asegurese de seguir cuidadosamente las instrucciones. Install net clips. Installez les pinces du filet. Netzhalteklammern anbringen.32 Install net clips. Installez les pinces du filet. Netzhalteklammern anbringen.32 Instale los sujetadores de la red. CLIP “ARM” " BRAS " DE LA PINCE CLIP-ARM "BRAZO" DEL SUJETADOR CLIP “BODY” " CORPS " DE LA P...