valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
Mrs. Jumbo and Timothy Q. Mouse peer out of the illuminated windows at the base of the pylon. Dumbo Pylon Inventory • Pylon •Two green wires • Dumbo figure • Owner’s Manual • Support arm • Service Center list • Switch Table of contents Wiring your Dumbo Pylon with a conventional power supply 3-4 Installing your Dumbo Pylon 5 Attaching the figure to your Dumbo Pylon 6 Operating your Dumbo Pylon with a conventional power supply 6 Operating your Dumbo Pylon with TrainMaster Command Control 7-8 Replacing the lamp in your Dumbo Pylon 9-11 Limited Warranty/Lionel Service 12 The following Lionel marks may be used throughout this instruction manual and are protected under law. All rights reserved. Lionel®, TrainMaster®, Odyssey®, RailSounds®, CrewTalk™, TowerCom™, DynaChuff™, StationSounds™, Pullmor®, ElectroCoupler™, Magne-Traction®, CAB-1 Remote Controller®, PowerMaster®, Lionel ZW®, ZW®, PowerHouse®, TMCC®, Lionelville™, Lockon® The name FasTrack® is used with permission from Pitsco, Inc. 2 Wiring your Dumbo Pylon with a conventional power supply W W iring your accessory is the first step in preparing for flight. The Dumbo Pylon will operate best at 12-18 volts (AC), and it can be powered through track power with a Lionel Lockon (available separately, 6-62900), or a FasTrack Accessory Power Wire (available separately, 6-12053), OR through an accessory power supply. We recommend that you choose a power supply that will allow you to increase or decrease the voltage to the accessory. Changing the voltage allows you to control the speed at which the figure circles the pylon. Figure 1 on page 4 illustrates the following procedure. To make proper connections, you need the insulation at the ends of the wires to be stripped back 1/4” to 3/8”. To strip the wires, use a pair of wire strippers. Caution! Only an adult should perform this task! Always use care when stripping wires. 1. Attach one wire to the #1 terminal of the track Lockon, a FasTrack Accessory Power Wire, OR the Power/A terminal on the accessory power supply. Connect it to one of the terminals on the separate switch (included with this accessory). 2. Attach an additional wire to the other terminal on the switch. Connect the other end of this wire to one of the spring-clip terminals at the bottom of the pylon. Note! To make the spring-clip terminal connections, press down on the “springy” top of the terminal clip so that a metal loop is formed. Slide the bare end of the wire into the exposed loop. Release pressure on the terminal clip, allowing the crimped metal to pinch the end of the wire in the metal loop. Give a little tug on the wire to check if the hold is secure. 3. Attach another wire to the #2 terminal of the track Lockon, a FasTrack Accessory Power Wire, OR the Common/Ground/U terminal on the accessory power supply. Connect it directly to one of the spring-clip terminals at the bottom of the pylon. At this point, your accessory is wired for power. The next section explains how to operate this accessory in a conventional (non-TrainMaster Command Control) environment. 3 Wiring your Dumbo Pylon with a conventional power supply (continued) POWER SUPPLY U A AU AU Mounting holes Mounting holes FasTrack Accessory Power Wire Figure 1. Wiring for conventional operation 4 Installing your Dumbo Pylon C C hoose a flat, level area on your layout for the accessory. Secure this accessory to your layout with four screws (not included) using the holes near the corners of the base. Be sure to wire your accessory before you secure it to your layout—the wire terminals are on the underside of the base. Keep in mind that Dumbo flies in a circle with diameter of 30”. The flight path must be kept clear. 5 Attaching the figure to your Dumbo Pylon C C omplete the assembly of your Dumbo Pylon by attaching the Dumbo figure and support rods to the structure. Figure 2 illustrates the following procedure. 1. Note that the supporting rod has different shaped ends. Insert the flattened end of the support rods into the tube protruding from the top of the pylon. Refer to the diagram for further assistance. 2. Insert the D-shaped ends of the wires into the openings in the bottom of the Dumbo figure. Support rod (bottom) Mounting hole, bottom of Dumbo Mounting hole on Support rod (top) top of pylon Figure 2. Installing the support rods Operating your Dumbo Pylon with a conventional power supply A A djust the voltage to the accessory to control the speed at which Dumbo circles the tower. Increasing the voltage will cause Dumbo to circle faster; decreasing the voltage will cause Dumbo to travel slower. To turn the accessory off, turn off the power supply or use the switch attached to the wires in Step 1 on page 3. 6 Operating your Dumbo Pylon with TrainMaster Command Control Y Y ou may choose to wire your accessory with an SC-2 Switch and Accessory Controller (available separately, 6-22980) or the Accessory Switch Controller (available separately, 6-14182). Refer to these manuals for add...