valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
Adult assembly is required. Tools required for assembly: Phillips Screwdriver, Hammer and Scrap Block of Wood (not included). Requires three "AA" batteries (included). Age: 2-6 years. Weight limit: 60 lbs (27 kg). sher-price.com Consumer Information #8 x 3" (7,6 cm) Screw – 1 #8 x 3/4" (1,9 cm) Screw – 4 Cap Nut – 1 FASTENERS SHOW ACTUAL SIZE WARNING TO AVOID SERIOUS INJURY: • Adult supervision is required. • Never use near cars and other motor vehicles, near streets, steps, sloped driveways, hills, roadways, alleys, swimming pools or other bodies of water. • Always wear shoes. • Never allow more than one rider. 2 Parts Not Shown: Label Sheet and Cap Nut Assembly Tool Seat Frame Pedal 2 Fork Covers Front Wheel Pedal Axle Fork Headlight Cover Seat Retainer Cap Straight Axle 2 Rear Wheels Handlebar 2 Hubcaps 2 Covers 4 Pedal Hubs #6 x ." (1,3 cm) Screw – 2 • Please save all packaging material until assembly is complete to ensure that no parts are discarded. • Please wipe each part with a clean, dry cloth before assembly. • Some parts shown are assembled to both sides of he trike. • Tighten assembled screws with a Phillips screwdriver. Do not over-tighten the screws. Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A. ©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc., unless otherwise indicated. PRINTED IN MEXICO W1442pr-0920 Assembly Rear Wheel CAUTION This product contains small parts in an unassembled state. Adult assembly is required. • Slide a hubcap (peg side up) onto the straight axle. • Slide a rear wheel (indented side down) onto the straight axle. • Turn the frame upside down. • Insert the straight axle through the holes in the rear of the frame. Rear Wheel (Indented Side Down) Hole Hole Frame Straight Axle Hubcap (Peg Side Up) Straight Axle 12BOTTOM VIEW Cap Nut (Indented Side Up) Cap Nut Assembly Tool Assembled Rear Wheel Straight Axle Hubcap (Peg Side Down) Frame Scrap Block of Wood Cover Hubcap 3 • Turn the frame on its side with the exposed end of the straight axle up. • Place the cap nut assembly tool under the assembled rear wheel and onto the cap nut. • Slide a rear wheel (indented side up) onto the end of the straight axle. • Slide a hubcap (peg side down) onto the straight axle. • Place a cap nut on the end of the straight axle. Tap the cap nut with a hammer. Gently pull the rear wheel up to be sure the cap nut is securely attached to the straight axle. • Insert one of the tabs on a cover into a slot in the hubcap. Push to snap the cover into place. Repeat this procedure to attach the other cover to the other hubcap. • Fit two pedal hubs onto the pedal axle tabs. Make sure the tabs fit into the slot in each pedal hub. Pedal Hub Pedal Hub Pedal Axle Tab Tab Slot 4 3 Assembly Pedal • While holding the pedal hubs on the pedal axle, insert the pedal axle through the hole in the center of the front wheel. • Push the pedal hubs into the center of the front wheel until they are flush with the surface of the front wheel. Hole Pedal Axle Pedal Hubs Front Wheel Pedal Hub Pedal Hub • Turn the front wheel assembly over. • Insert the remaining pedal hubs on top of and below the pedal axle and into the hole in the center of the front wheel. • Push the pedal hubs into the center of the front wheel until they are flush with the surface of the front wheel. 56 • Fit the pedal on the pedal axle. Tap the pedal with a hammer until it is secure. • Pull the pedal up to be sure it is secure. If you can remove it, you have not secured it properly. Tap it with the hammer again. Pedal Axle Scrap Block of Wood Fork Arms Pedal Axle Groove Fork Cover 78 • Place the front wheel assembly between the fork arms. Make sure the pedal axle fits into the groove at the bottom of each fork arm. • Place a fork cover over the pedal axle on one fork arm. • Insert two #8 x 3/4" (1,9 cm) screws into the fork cover and tighten. • Repeat this procedure to attach the other fork cover to the other fork arm. 4 • Insert the fork post up through the hole in the neck of the frame. Make sure the fork is positioned so that the fork covers face the rear wheels. • Place the handlebar onto the fork post and push it down onto the frame. Make sure the handlebar is positioned so that the screw hole faces the rear wheels and aligns with the screw hole in the fork post. Hint: You may need to rotate the handlebar to align the holes. • Insert the #8 x 3" (7,6 cm) screw through the hole in the handlebar and into the fork post so that part of the screw (about 3/4"/1,9 cm) is still visible. Tighten the screw. Handlebar Frame Neck Fork Post Fork Cover Rear of Trike • Position the seat upside down. • Fit the small pegs on the seat retainer into the holes in the seat. • Insert and “snap” the cap into the hole in the frame. Cap Seat Retainer Seat Peg Holes • Fit the tab on the headlight cover to the slot in the top of the handlebar. • Insert two #6 x 1/2" (1,3 cm) screws screws into the h...