valutazioni - 4, GPA: 3.8
(
)
)
|
Facilità d'uso
Do not .leave it in an automobile exposed to direct sunlight for a long time with the doors and windows closed as this may deform the cabinet. •Avoid cuts, scratches, or poor connections in the AC power cord, as they may result in possible fire or electric shock hazard. Aiso, excessive bending, pulling or splicing of the cord should be avoided. •Do not unplug the AC power cord by pulling on the cord. To do so may cause premature failure or shock hazard. •Do not operate the set on AC power in a bathroom, as a potential shock hazard may result. •When not in use, disconnect the AC power cord from the AC power outlet. Max. 40°C CASSETTE TAPES Use only good-quality tapes up to the length of C-90. Do not use C-120 tapes with this unit because these tapes can easily become broken or stretched if not used with extreme care and may get tangled with the Capstan and Pressure roller. OK Pencil If the tape loosens, take up the slack by turning the reel in the proper directions. Notes: •Use normal type of cassette tapes only, if other tapes are used, you may not obtain optimum performance. •Cassettes, both recorded and unrecorded, should not be stored in locations with high temperature, high humidity or direct sunlight Never place a recorded cassette near a magnetic source, such as a magnet or a TV set as this may affect tape performance. Do not handle, or pull the tape out of the cassette. -2 - POWERSOURCE ■ Battery Operation 1. Open the Battery Compartment cover as shown in the figure. 2. Insert 6 UM-1 size (Panasonic R20/LR20 or equivalent) batteries into the Battery Compartment, making sure that the proper polarities are maintained, and that the batteries are installed in the specified numerical order. Lower Shelf @ ® Upper Shelf (+) c[ 6 ^ 5 c( 4 © 3. Replace the compartment cover. Notes; •Batteries installed with incorrect polarities may leak and damage this unit. •Do not mix batteries (old and new) or types (carbon and alkaline). •Battery removal Remove as shown in the figure below. Upper Shelf PUSH UP Lower Shelf ? SCO To Prevent Possible Damage to This Unit •Load new batteries with their polarities (© and ©) aligned correctly. •Do not apply heat to batteries, or internal short-circuit may occur. •If this unit is not to be used for a long period of time, or used on AC power source, remove all batteries and store them in a cool and dry place. •Remove spent batteries immediately and dispose of them. •Do not use old and new batteries together. Also never use an alkaline battery with a manganese battery. •Battery life When the batteries are weak, the tape speed will slow down, the sound will become distorted, and the volume will decrease. If the set is not used for a long period of time or is used only from an AC power source, remove all the batteries to prevent potential damage due to possible battery leakage. ■ AC Power Operation Connect the included AC power cord to the AC Socket in the unit and your household AC power outlet. AC IN — AC power cord AC power outlet AC 240 V Note: To operate on battery power, unplug the AC power cord from the household AC power outlet and the AC Socket on the unit. - 3 - LOCATION OF CONTROLS ООО О ©О ООО Panasonic I |_ J г........... □ 2 H Ь О & o Headphones Jack (PHONES) 0 Built-in Microphone (MIC) 0 Volume Control (VOLUME) Q Tone Control (TONE) 0 Function Selector (SELECTOR) © Tape 1 (For Playback) / Pause Button (KI PAUSE) Stop/Eject Button (H STOP/EJECT) Fast Forward Button (<* FF) Rewind Button (►► REW) Playback Button (< PLAY) 0 CD/Line Input Jacks ({ÇD]/LINE IN) 0 Editing Mode Selector/Beat Proof Switch (EDIT1NG/B.P) 0 Band Selector (BAND) 0 Tuning Control (TUNING) 0 Speakers [Tweeter] 0 Speakers [Woofer] 0 Tape 2 Cassette Compartment 0 FM Stereo Indicator (FM STEREO) 0 Tape 1 Cassette Compartment 0 Handle 0 Telescopic Antenna 0 AC Socket (AC IN~) 0 Battery Compartment 0 Tape 2 (For Recording and Playback) Pause Button (I I PAUSE) N Stop/Eject Button (B STOP/EJECT) Fast Forward Button (<« FF) Rewind Button (►► REW) Playback Button PLAY) Record Button (• I RECORD!) -4 - RADÍO TAPE PLAYBACK (ТАРЕ 1/TAPE 2) 1. Set the Function Selector to "RADIO”. 2. Set the Band Selector to the desired radio band. 3. Tune in your favorite station using the Tuning Control. 4. Adjust the Volume and Tone Controls to the desired settings. 5. The radio can be turned off by setting the Function Selector to “TAPE/POWER [off]”. Notes: •To receive FM stereo broadcasts, set the Band Selector to “FM STEREO”. The FM Stereo indicator will light during stereo broadcasts. •If FM stereo reception is poor (excessive noise, FM Stereo Indicator flickers), set the Band Selector to “FM". This will reduce the noise and provide clear reception; however, the broadcast will not be heard In stereo. This unit has a dual cassette system. A tape can be played back with Tape 1 and Tape 2, ■ Single Tape Playback 1....