valutazioni - 1, GPA: 3
(
)
)
|
Facilità d'uso
indents of the battery door (at the back end o. the transmitter) and gently pull down (see Fig. ure 3). 2. Turn on the transmitter by sliding the powe. switch (closest to the battery compartment. forward to its on position, toward the mic ele. ment. The red battery condition light shoul. flash once and then go out. If the red LE. stays on or illuminates during a performance. it should be replaced immediately. The gree. LED will stay lit when the transmitter is on. 3. Check reception. Observe that the audi. carrier light on the front panel of the receive. is illuminated, an indication that the receiver i. picking up the signal. Then, .walk. the in. tended area of use and make sure that ther. are no barriers to reception or sources of in. terference. 4. Unmute the audio by sliding the audio switc. (immediately below the mic element) toward. the windscreen. 5. Adjust the gain if necessary. First, speak o. sing into the microphone and listen closely fo. distortion or hiss. If the gain is too low or high. adjustments are necessary. Gently insert th. provided screwdriver (or other 3/32-in. screw. driver) into the hole near the head of th. transmitter (see Figure 4). Turn lightly unti. the screwdriver tip drops into the slot in th. level control. Gently turn counterclockwis. until the control stops (the mic output is at. tenuated but not .off.). Slowly turn the mic. level control while listening to the audio. If th. audio becomes distorted, turn the mic leve. control counter-clockwise about 1/8 turn. 6. Adjust the squelch control if necessary. The squelch control on the back of the re. ceiver may be adjusted to increase range o. reduce interference. Turn the control counter. page . R200 OWNERS MANUA. clockwise to increase range. Caution! In. transmitter off. Turn the squelch contro. creasing the range will make the syste. counter-clockwise until you hear noise or in. more susceptible to outside interference. terference. Then, turn the squelch clockwis. If the squelch is being adjusted, turn th. until the noise is gone. Figure . BODYPACK TRANSMITTER SETU. 1. Insert battery. Open the hinged battery com. partment by placing your thumb or finger o. the indent on the battery door and pull down. When inserting the battery, pay attention t. the polarity (+/-) and insert the terminals int. the battery compartment first. Close the bat. tery door by sliding the door shut. 2. Turn on the transmitter by sliding the powe. switch to its on position. Check the conditio. of the battery by looking at the LED below th. power switch. The red battery light shoul. flash once and then go out. If the LED stay. on, the battery is weak and should be re. placed. 3. Prepare the audio source by attaching th. lavalier microphone to the user, placing th. headset on the user.s head or plugging th. cable into the instrument (depending on wha. type of system you have). Keep the audi. muted while plugging in and adjusting th. microphone or source. Placement o. lavalier and headset microphones will notice. ably change the sound quality, so some ex. perimentation with the user is necessary. BELT CLIP MAY BE TURNED 90 DEGREES BY REMOVING SCREW AND REINSTALLING HERE. GAIN ADJUSTMENT DOOR OPENED BUT NOT SWUNG UPWARD SWING DOOR UPWARD TO ACCESS BATTERY COMPARTMENT TO OPEN BATTERY DOOR PRESS ARROW WITH INDEX FINGER AND PULL DOWN WITH THUMB AND MIDDLE FINGER 4. Check reception by observing that the R. carrier light is illuminated on the receiver.. front panel. 5. Turn on the audio transmission by slidin. the large mute switch to the .on. position. 6. Listen carefully to the audio and be sensi. tive of overload distortion and low gain o. hiss. 7. Adjust the gain if necessary. Gently inser. the provided screwdriver or other 3/32-in. (2.. mm) screwdriver into the gain adjustment lo. cated at the top edge of the battery compart. ment under the door. The door has to b. opened but not swung upward to make ad. justments. Turn lightly until the screwdriver ti. drops into the slot on the level control. Gentl. turn the control counterclockwise until th. control stops (the audio output is attenuate. but not .off.). Slowly turn the audio level con. trol clockwise while listening to audio; if th. audio becomes distorted, turn the mic leve. control counter-clockwise about 1/8 turn. 8. Clip the bodypack to the user.s belt or to . pocket. The bodypack can be positioned hori. zontally or vertically by moving the belt cli. attachment. Removing the belt clip attach. ment screw and moving it 90 degrees wil. change the orientation. MIC OR GUITAR POWER AUDIO CABLE SWITCH SWITCH ENTRY POWER ON ON AUDIO BATTERY LIGHT page . R200 OWNERS MANUA. COMPATIBILIT. The receiver and transmitter must be on the sam. UHF frequency to operate together. Because o. the specialized equipment required to adjus. these units properly, users cannot change the fre. quencies or make any internal adjustments. If two or more R200 and/or other VHF/UHF wire. less systems are being used in the same locatio...