valutazioni - 4, GPA: 3.5
(
)
)
|
Facilità d'uso
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Reversing the Door Swing Wine Chiller To reverse the door Parts included: 1. Top left case hinge 2. Bottom left case hinge 3. Left and right side decorative hinge cover 4. Decorative hinge screw hole cover 5. Torx® driver bit Tools required: 1. Phillips screwdriver 2. Electric drill To remove the door: 1. Flatten the shipping carton to use as a pad. 2. Remove the 2 screws and the toekick. Set aside the screws and toekick for final installation. 3. Use the supplied Torx® bit and electric drill to remove the 3 screws holding the top case hinge. Lift off the hinge. (Screws will be used to install the new hinge.) 4. Lift the door off the bottom case hinge. 5. Remove the bottom case hinge pin and bracket. Rotate the door: The handle will be on the right side of the door; hinges will be installed on the left side of the case. 1. Remove the door stop and cam riser on the original bottom right side of the door. 2. Remove the fill plug on the top right side of the door. 3. Turn the door over and reinstall the fill plug on the new left side. To reinstall the door: 1. Install the original door stop and cam riser onto the bottom left side of the door. 2. Install the new supplied bottom case hinge pin and bracket onto bottom left side. Remove Top Hinge Remove Hinge Install 3 Hinge Screws Door Stop and Cam Riser Hinge Pin and Bracket 3. Place the door onto the bottom case hinge. 4. Install the supplied left-hand top case hinge with the 3 original screws. 5. Select the hinge cover marked with an “L”. 6. Peel backing off the tape inside the decorative hinge cover. 7. Press and snap the Install Covers hinge cover into place. 8. Snap the screw hole cover into place on the opposite side. Important: Check to be sure screws are tight and that the door is straight and does not sag. The door should swing freely. NOTE: See Installation Instructions to apply hinge cover and screw hole cover. Position nameplate: Apply the Monogram nameplate on the door using the template included in the installation instructions. The Problem Solver Wine Chiller Normal Newer appliances sound different from older appliances. Modern appliances have more features and use newer technology. operating sounds Do you hear what I hear? These sounds are normal. HUMMM... WHOOSH... • The new high efficiency compressor may run faster and longer than your old appliance and you may hear a high-pitched hum or pulsating sound while it is operating. • Sometimes the appliance runs for an extended period, especially when the doors are opened frequently. • You may hear a whooshing sound when the doors close. This is due to pressure equalizing within the appliance. CLICKS, POPS, CRACKS and CHIRPS • You may hear cracking or popping sounds when the appliance is first plugged in. This happens as the appliance cools to the correct temperature. • Expansion and contraction of cooling coils during and after defrost can cause a cracking or popping sound. • You may hear the fans spinning at high speeds. This happens when the appliance is first plugged in, when the door is opened frequently or when large amounts of beverages are added to the appliance. The fans help maintain desired temperatures. • If the door is open for over 3 minutes, you may hear a fan come on in order to cool the appliance. • The fans change speeds in order to provide optimal cooling and energy savings. WATER SOUNDS • The flow of refrigerant through the appliance cooling coils may make a gurgling noise like boiling water. • A water dripping noise may occur as water from the evaporator flows into the drain pan. • Closing the drawer may cause a gurgling sound due to pressure equalization. The Problem Solver Wine Chiller Questions? PROBLEM POSSIBLE CAUSE Use this problem solver! APPLIANCE • Appliance may be in defrost cycle when motor does not operate for DOES NOT OPERATE about 30 minutes. • If interior light is not on, appliance may not be plugged in at wall outlet. Push the plug completely into the wall outlet. • The fuse is blown/circuit breaker is tripped. Replace fuse or reset the breaker. VIBRATION OR RATTLING (Slight vibration is normal.) • Adjust the leveling legs as shown in the Installation Instructions. MOTOR OPERATES • Normal when appliance is first plugged in. Wait 24 hours for the FOR LONG PERIODS appliance to completely cool down. OR CYCLES ON AND • Often occurs when large amounts of beverages are placed in appliance. OFF FREQUENTLY This is normal. • Door left open or package holding door open. • Hot weather or frequent door openings. This is normal. • Temperature control set at the coldest setting. See Temperature Control. Allow 24 hours for temperature to change. COMPARTMENT • Temperature control not set cold enough. TOO WARM See Temperature Control. Allow 24 hours for temperature to change. • Warm weather or frequent door openings. • Door left open for long time. • Package may be ho...