valutazioni - , GPA:
(
)
)
Produttore : Culligan
File Size : 56.01 kb
File Nome : 008a5bec-6f4c-4ff6-a816-69683325627a.pdf
Lingua di insegnamento: 
Il documento viene caricato, si prega di attendere
 |
Il documento viene caricato, si prega di attendere
Facilità d'uso
Failure to do so may result in cracking of the filter and water leakage. NOTE: Make certain that installation of this system complies with all state and local laws and regulations. FOR COLD WATER USE ONLY. MAINTENANCE: Contact your area retailer for replacement cartridges and pricing or call Culligan Customer Service at 800-634-1455 for the nearest dealer. Change cartridge every 2500 gallons or approximately every 12 months. Filter Installation Instructions (For copper or plastic tubing) NOTE:Shut off water supply when replacing filter. 1. Shut off water supply. Select a location for installation on 1/4" OD (outsidediameter) plastic or copper tubing. Filter requires at least threeinches behind appliance. See Fig 1. NOTE: Leave at least a 5-foot coil of tubing between appliance side and compression fittings. This will allow room to pull out the appliance for changing the filter. 2. Wrap 6" of Teflon tape around the threads of both ends of fittings. Screw fittings into the body of the filter until hand tight. Use a wrench to tighten two additional turns. DO NOT OVER-TIGHTEN. About one full thread should remain visible. 3. Two types of compression nuts are included: One for copper tubing and one for plastic tubing. Copper tubing uses nuts with metal grippers, while the plastic tubing uses the nuts with plastic grippers. Refer to Fig. 2. DO NOT DISASSEMBLE NUTS. If nuts become disassembled, refer back to Fig 2 for reassembly. Attach correct compression nuts to fittings. 4. Cut 1/4" OD tubing where filter will be installed. 5. On the inlet side of filter, insert tubing as far as possible into fitting. WATER FLOWS IN DIRECTION INDICATED BY ARROW ON THE FILTER. See Fig 3. If tubing does not enter the fitting, loosen the nut one turn. After inserting tubing, hand tighten nut first, then tighten 1-1/2 to 2 turns with a wrench. 6. With only the inlet side connected, flush water thru filter into a container for 5 minutes. Wait an hour, and then flush another 5 minutes, or until water runs clear.* 7. Shut off water and then connect the outlet side of the filter to the appliance using the procedure in step #5. Turn water on and check for leaks. *NOTE: Though the filter has been rinsed to remove fine particles of carbon, resettling of the carbon within the filter can occur. If the first trays of ice become discolored, discard the ice until clear. Figure 1 Figure 2 Figure 3 Metal Gripper Outlet To Refrigerator Supply Side Plastic Gripper Inlet Performance Data Important Notice: Read this performance data and compare the capabilities of this system with your actual water treatment needs. It is recommended that, before installing a water treatment system, you have your water supply tested to determine your actual water treatment needs. This system has been tested according to NSF/ANSI Standard 42 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration of less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI standard 42. Substance Influent Challenge Max. Permissible Product Reduction Minimum Average Concentration Water Concentration Requirements Reduction Reduction Standard 42 Chlorine 2.0 mg/L±10% . 50% >93% Flow Rate=0.75 gpm (2.8 L/min) Capacity=2500 gallons (9463 L) or 12 months Testing was performed under standard laboratory conditions, actual performance may vary. Test Conditions: Operating Requirements: Flow Rate = 0.75 gpm (2.8 L/min) Pressure = 30-125 psi (2.07-8.62 bar) Inlet Pressure = 60 psi (4.14 bar) Temperature = 40.-100. F pH = 7.5 ±1 (4.4.-37.7. C) Temperature = 68. F ± 5. F Turbidity = 5 NTU Max (20. C ± 2.5. C) The IC-100 is Tested and Certified by NSF International to NSF/ANSI Standard 42 for the reduction of Chlorine, Taste and Odor. IOWA RESIDENTS ONLY: Store or seller’s name Address City State Zip Telephone Seller’s signature Customer’s signature Date QUESTIONS? Call Culligan Customer Service: 1-800-634-1455, Mon.-Fri., 7:30 AM-7 PM CST Culligan International Company Culligan Sales & Marketing Correspondence One Culligan Parkway Customer Service M-F 7:30 a.m – 5:00 p.m. CST P.O. Box 1086 • Sheboygan, WI 53082-1086 Northbrook, Illinois 60062 Phone: 1-800-634-1455 Fax: 1-888-749-8826 Fax (847) 291-7632 International: Phone (920) 457-9435 • Fax (920) 457-2417 e-mail: sales-marketing@culligan.com e-mail: customerservice@culligan.com ©2004 Culligan International Company, Printed in U.S.A. 145233 Rev D 03/04 Filtro Desechable para Hacedor de Hielo/Dispensador de Agua Manual para el Uso y el Mantenimiento Modelo IC-100 Precauciones una calida desconocida sin desingectarla adecuadamente antes o despues del sistema. PRECAUCION: este filtro debe de protegerse contra la congelacion, que puede causar ADVERTENCIA: no usar con agua contaminada microbiologicamente o si es de grietas y goteras. NOTE: asegurese de obedecer con todas las reglas locales y estatales ...