valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
Apply a thick bead, approximately. 1/4" (6mm) diameter, of NSF listed silicone sealant (Dow- Corning RTV-732 or equivalent) 1/4" (6mm) inside marked outline of dispenser. 11. Carefully position dispenser on counter. 12. Remove four screws securing splash panel to front of dispenser and gently lay splash panel on counter. (Water line to solenoid valve can be disconnected from water inlet valve by pushing on ring at end of inlet fitting while pulling on tubing.) 13. Secure dispenser to counter with four 3/8" bolts (supplied by others). 14. Smooth excess sealant around outside of dispenser. 15. Run water supply line from back of dispenser through utility knock-out (Figs. 4, 5) or up through counter cut-out. Connect water supply line to 3/8" FPT, (Fig. 3J) fitting on utility flange at bottom of dispenser. 16. Remove 3/4" drain connection plug from either fitting at rear of dispenser, (Fig. 1K) or internal fitting, (Fig. 3L), as appropriate. Connect and run a dedicated drain line to wall or floor drain. An air break should be provided. If dispenser is equipped with a top mount, water-cooled icemaker complete steps 17 through 20. If equipped with a top mount, air-cooled icemaker proceed to step 21. 17. Connect icemaker water supply line to 3/8" FPT water inlet, (Fig. 4M). 18. Connect icemaker drain line to 3/4 MPT drain connection (Fig, 4N). 19. If icemaker is water-cooled, connect water-cooled condenser supply line to 3/8" FPT condenser fitting on back of dispenser (Fig. 4R). Note: Do not run condenser supply water through icemaker water filter system. 20. Connect condenser drain line to 3/8" FPT fitting on back of dispenser (Fig. 4P). Important: Do not connect condenser drain line to any other drain lines. 21. Proceed with either Satellite-fill or top-mounted icemaker connection instructions, as appropriate. Fig. 4 – Rear connections, countertop models with integral icemakers access panel (M) 3/8" FPT icemaker water inlet (R) 3/8" FPT condenser inlet (water-cooled only) (P) 3/8" FPT condenser outlet (water-cooled only) (N) 3/4" MPT icemaker drain (H) utility knock-out Fig. 5 – Rear connections, countertop models with Satellite-fill icemakers (G) ice transport tube knock-out access panel (H) utility knock-out 11 Installing Satellite-fill icemakers Models110CR400A/W ! See Icemaker Installation Manual (form #208600) for critical installation instructions for remote icemakers. Failure to comply with these instructions will result in poor performance and void warranty. 1. Install Satellite-fill icemaker following instructions in icemaker manual. 2. Run uninsulated ice transport tube from dispenser through ice transport tube knock-out, (Fig. 5G) or through counter opening to icemaker. 3. Insulate ice transport tube by sliding insulation over tube. 4. Adjust insulation to cover all exposed ice transport tubing including tubing inside dispenser cabinet. 5. Check that insulated ice transport tube runs continuously uphill (with no dips) from icemaker to dispenser. 6. Run bin signal wire from dispenser through utility knockout, (Fig. 5F) or counter cutout to the icemaker and connect bin signal wire (two-conductor twist lock) to bin signal plug on icemaker. 7. Plug dispenser power cord into 20 amp rated NEMA 5-20 wall socket. 8. Turn on dispenser water supply and check for leaks. Replace splash panel. 9. Remove top front cover by removing two screws at bottom corners of cover. Lift cover slightly and pull forward. Turn on power and bin signal rocker switches. Replace front cover and secure with screws. Test operation. 10. Clean and sanitize icemaker following instructions in icemaker manual. Discard sanitized ice. 11. Clean and sanitize dispenser hopper following instructions on page 14. Installation is complete. Fig. 6 – Ice transport tube and ice level control stat mounting for freestanding dispensers and countertop units with Satellite-fill icemaker engaging pin 3/16 (5mm) ice tube hole ice hose mounting bracket ice level control stat ice tube 1" (26mm) Installing top mount icemakers Models 110CT400A/W ! Dispensers with top mount icemakers cannot be mounted on legs.They must be bolted to counter. Use gloves when lifting icemaker to protect hands from sheet metal edges. 1. Remove dispenser top front cover by removing two screws at bottom corners of cover, lifting cover slightly and pulling forward. 12 2. Remove dispenser top front cover by removing two screws at bottom corners of cover, lifting cover slightly and pulling forward. 3. Remove icemaker compartment top and side panels. 4. Remove icemaker hold-down bracket from front of icemaker compartment. 5. Lift icemaker onto dispenser top and slide icemaker completely into position, compressor end first. Front of icemaker base must be flush with front of dispenser. 6. Reinstall hold down bracket on front of icemaker with power cord and bin signal cords in notch. Do not cut or pinch cords. 7. Insert loose end of ice transport tube through bracket (on icemaker base) into ho...
Questo manuale è adatto anche per i modelli :Dispenser - 110CR400A/W (1.38 mb)
Dispenser - 110FB400A/W (1.38 mb)