valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
7 and 8) using wall bracket as template. 5. Lift dispenser onto wall bracket, positioning unit so that hook on back of dispenser is captured by wall bracket support angle (Fig. 6, hook detail). ! Do not rest dispenser weight on bottom front edge of wall bracket. 6. Install four 1/4-20 screws through bottom of wall bracket into bottom of dispenser to secure dispenser to bracket. 7. Remove splash panel. Water line to solenoid valve can be disconnected from water inlet valve by pushing on ring at end of inlet fitting while pulling on tubing. Fig. 6 – Side view and angle detail for wall mount units without drain pan with integral icemaker (in top of cabinet). Wall mount units with Satellite-fill icemakers will not require installation of a filler strip. 13.5" (343mm) 18" (457mm) 23" (584mm) 16.875" (429mm) 18.5" (470mm) 21.5" (546mm)2.5" (64mm) 17.125" (435mm) 24" (610mm) 25HT400A/W 12" (305mm) 50HT400A/W 16" (406mm) 25HT400A/W 44" (1118mm) 50HT400A/W 48" (1219mm) support angle and hook detail 11 8. Remove utility knock-out (Fig.4, 5F) from rear of dispenser and install supplied protective grommet. For dispensers using remote icemakers, remove ice transport tube knock-out (Fig. 5G) from rear of dispenser. 9. Run water supply line from back through utility knock-out (Fig. 5F) and connect water supply line to 3/8" FPT fitting on utility flange at bottom of dispenser (Fig. 3G). 10. Connect and run a dedicated drain line from 3/4" drain tube to wall or floor drain. An air break should be provided. 11. Proceed with either remote or top-mounted icemaker connection instructions, as appropriate. Fig. 7 – Mounting dimensions for wall mount Fig. 8 – Mounting dimensions with wall mount units units without drain pan with Satellite-fill icemaker without drain pan with integral icemaker 16" 20.875" (530mm) filler strip 17.8" (445mm) 3/8" fasteners 25HT400A/W 25.5" (648mm) wall bracket 50HT400A/W 29.5" (749mm) (121mm) 3.5" (89mm) 4.75" (121mm) 3.5" (89mm) 11.5" (292mm) 16" (406mm) wall stud 25HT400A/W 9.5" (241mm) 50HT400A/W 11.5" (292mm) 25HT400A/W 9.5" (241mm) 50HT400A/W 11.5" (292mm) utility cut-out 1.375" access opening (35mm) cover wall bracket – bottom view access opening cover wall bracket 3.5" (89mm) 1.375" (35mm) 4.75" 3.5" (89mm) 11.5" (292mm) 3/8" fasteners (406mm) wall stud 25HR400A/W 25.5" (648mm) 50HR400A/W 29.5" (749mm) 25HT400A/W 9.5" (241mm) 50HT400A/W 11.5" (292mm) 25HT400A/W 9.5" (241mm) 50HT400A/W 11.5" (292mm) utility cut-out wall bracket – bottom view 12 Installing Satellite-fill icemakers Models 25CR400A/W, 50CR400A/W, 25HR400A/W, 50HR400A/W ! See Icemaker Installation Manual (form #208600) for critical installation instructions for Satellite- fill icemakers. Failure to comply with these instructions will result in poor performance and void warranty. 1. Install Satellite-fill icemaker following instructions in icemaker manual. 2. Run uninsulated ice transport tube from dispenser through ice transport tube knock-out (Fig. 5G) or through counter opening to icemaker. 3. Insulate ice transport tube by sliding insulation over tube. 4. Adjust insulation to cover all exposed ice transport tubing including tubing inside dispenser cabinet. 5. Check that insulated ice transport tube runs continuously uphill (with no dips) from icemaker to dispenser. 6. Run bin signal wire from dispenser through utility knockout (Fig. 5F) or counter cut-out to icemaker and connect bin signal wire (two-conductor twist lock) to bin signal plug on icemaker. 7. Plug dispenser power cord into 20 amp rated NEMA 5-20 wall socket. 8. Turn on dispenser water supply and check for leaks. Replace splash panel. 9. If dispenser is equipped with SensorSAFE remove protective plastic coating from dispenser lenses. 10. Remove top front cover by removing two screws at bottom corners of cover. Lift cover slightly and pull forward. Turn on power and bin signal rocker switches. Replace front cover and secure with screws. Test operation. 11. Clean and sanitize icemaker following instructions in icemaker manual. Discard ice made during sanitizing process. 12. Clean and sanitize dispenser hopper following instructions on page 16. Installation is complete. Fig. 9 – Ice transport tube and ice level control stat mounting for freestanding dispensers and countertop units with Satellite-fill icemaker engaging pin .187 (5mm) ice tube hole ice hose mounting bracket ice level control stat ice tube 1" (25mm) 13 Installing top mount icemakers Models 25CT400A/W, 50CT400A/W, 25HT400A/W, 50HT400A/W ! Dispensers with top mount icemakers cannot be mounted on legs.They must be bolted to counter. Use gloves when lifting icemaker to protect hands from sheet metal edges. 1. On dispensers equipped with top-mounted, water-cooled icemakers, feed condenser supply and drain lines from back through utility knock-out (Fig. 4F) or through counter, as appropriate. Connect condenser supply line to inlet fitting (Fig. 3H) on utility flange at bottom of dispenser. Connect condenser drai...
Questo manuale è adatto anche per i modelli :Dispenser - 25 (1.55 mb)