valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
Lift junction box and power cord up until cord and mounting screws clear notches on rear panel of dispenser. Remove Phillips head screws from right side of junction box. 8. Rotate junction box 90 degrees so that screw holes on right side of junction box align with holes on rear dispenser panel. Resecure junction box to dispenser using Phillips head screws. 9. Place power cord inside dispenser and replace access panel (Figs. 4, 5) to rear of dispenser. Note: For dispensers to be installed with utilities connected through rear of dispenser, it may be easier to make preliminary connections before dispenser is set in place. 10. Apply a thick bead, approx. 7mm (1/4") diameter, of NSF listed silicone sealant (Dow Corning RTV-732 or equivalent) 7mm (1/4") inside marked outline of dispenser. 11. Carefully position dispenser on counter. 12. Remove four screws securing splash panel to front of dispenser and gently lay splash panel on counter. (Water line to solenoid valve can be disconnected from water inlet valve by pushing in on release ring at end of inlet fitting while pulling on tubing.) 13. Secure dispenser to counter with four 10mm (3/8") bolts (supplied by others). 14. Smooth excess sealant around outside of dispenser. 15. Run water supply line from back of dispenser through utility knock-out (Figs. 4, 5F) or up through counter cut-out. Connect water supply line to 10mm (3/8") push-in fitting on (Fig. 3G) utility flange at bottom of dispenser. 16. Remove 19mm (3/4") drain connection plug from either fitting at rear of dispenser (Fig. 3L) or internal fitting (Fig. 3K), as appropriate. Connect and run a dedicated drain line to wall or floor drain. An air break should be provided. 17. Proceed with either remote or topmounted icemaker connection instructions, as appropriate (p. 13, 14). Fig. 4 – Rear connections, countertop models with integral icemakers access panel knock-out (F) 149mm (5.875") drain utility connection 19mm (3/4") FPT 20mm 375mm 267mm (14.75") (10.5") (.8") Fig. 5 – Rear connections, countertop models with Satellite-fill icemakers 267mm (10.5") 162mm (6.375") 375mm (14.75") ice utility connection 19mm (3/4") FPT drain 20mm (.8") access panel knock-out (F) transport tube knock-out (G) 149mm 5.875" 10 Installing wall mount dispensers 1. Install supplied wall bracket with six 10 mm (3/8") diameter fasteners as shown in Fig. 7. Note: Three holes are available at each fastening site to allow capture of studs/support within wall. Steps 2 - 3 are required for models with integral icemaker only (C/E25HT400A/W and C/E50HT400A/W). 2. For models with integral icemaker, use straight edge to position filler strip flush with top edge of wall bracket. 3. Fasten filler strip to wall as shown in Fig. 8. 4. For all models, cut utility hole in wall (Figs. 7 and 8) using wall bracket as template. 5. Lift dispenser onto wall bracket, positioning unit so that hook on back of dispenser is captured by wall bracket support angle (Fig. 6, hook detail). ! Do not rest dispenser weight on bottom front edge of wall bracket. 6. Install four 1/4-20 screws through bottom of wall bracket into bottom of dispenser to secure dispenser to bracket. 7. Remove splash panel. Water line to solenoid valve can be disconnected from water inlet valve by pushing on ring at end of inlet fitting while pulling on tubing. Fig. 6 – Side view and angle detail for wall mount units without drain pan with integral icemaker (in top of cabinet). Wall mount units with Satellite-fill icemakers will not require installation of a filler strip. 1118mm (44") 343mm 458mm 584mm 429mm 305mm (12") 470mm 546mm 64mm 435mm 610mm (24") (2.5") (23") (16.875") (18") (21.5") (17.125") (13.5") (18.5") C/E25HT400A/W C/E50HT400A/W 406mm (16") C/E25HT400A/W C/E50HT400A/W 1219mm (48") support angle and hook detail 11 8. Remove utility knock-out (Fig.4, 5F) from rear of dispenser and install supplied protective grommet. For dispensers using Satellite-fill icemakers, remove ice transport tube knock-out (Fig. 5G) from rear of dispenser. 9. Run water supply line from back through utility knock-out (Fig. 5F) and connect water supply line to 3/8" FPT fitting on utility flange at bottom of dispenser (Fig. 3G). 10. Connect and run a dedicated drain line from 3/4" drain tube to wall or floor drain. An air break should be provided. 11. Proceed with either Satellite-fill or top-mounted icemaker connection instructions, as appropriate. Fig. 7 – Mounting dimensions for wall mount units without drain pan with Satellite-fill icemaker 407mm (16") wall stud 10mm (3/8") fasteners wall bracket 35mm (1.375") access opening cover 648mm 89mm (3.5") 121mm 89mm (3.5") 292mm 242mm (9.5") utility cut-out (25.5") (4.75") (11.5") C/E25HR400A/W C/E50HR400A/W C/E25HT400A/W C/E50HT400A/W 750mm (29.5") 292mm (11.5") 241mm (9.5") C/E25HT400A/W C/E50HT400A/W 292mm (11.5") wall bracket: bottom view Fig. 8 – Mounting dimensions with wall mount units without drain pan with integral icemaker 530mm (20.875") fill...
Questo manuale è adatto anche per i modelli :Dispenser - C/E25CR400A/W (1.38 mb)
Dispenser - C/E25HR400A/W (1.38 mb)
Dispenser - C/E25HT400A/W (1.38 mb)
Dispenser - C/E50CR400A/W (1.38 mb)