valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
2) Fill hopper with product. Allow barrel to fill with product to the proper level, then install carb tube. 3) Turn power switch (toggle switch located underneath the electrical box) to "on" position. 4) Turn mode switch (rocker switch located next to power switch) to freeze position. 5) Allow product to freeze in barrel. 6) To dispense product pull down valve handle and release when done. 7) If product consistency is not as desired, adjust per the instructions on page 9. Mix Considerations - General Freezing characteristics are affected by the amount of sweeteners and solids in the mix, called BRIX. BRIX can be measured with an instrument called a refractometer. A BRIX reading of between 11 and 14 will provide optimum freezer operation. Mixes with this brix level will freeze down to a smooth, uniform consistency. Mixes with too high a brix level will take longer to freeze down and will yield a soft, wet, frozen product. Mixes with too low a brix level will have larger ice crystals and will have a tendency to dispense slowly. Note: Always take BRIX measurements using mix that has been thoroughly blended, before it is frozen. Always allow frozen mix to thaw thoroughly before taking a reading. Alcohol content also affects product-freezing characteristics and may prevent the freezer from serving a product at proper thickness. For maximum output capacity always pre-chill mix before adding it to the freezer. Pre-chilled mix gives the freezer a head start on the freezing process and will speed both initial freeze down and recovery time. Page 6 Crathco® 5000 Series Manual Carburetor Assembly Your new freezer uses a metering device, known as a carburetor, to feed the proper ratio of mix and air into the freezing cylinder. For products such as dairy based shake mixes, the proper mix to air ratio is generally accepted to be two parts mix to one part air. This proportion yields a finished product that is both tasty and profitable. At this ratio, one gallon of liquid mix will yield a volume of one and one-half gallons of frozen product. The carburetor is a tube with a hole, or series of holes, bored through the side. It is located in the hopper and fits in a hole that leads to the freezing cylinder. Air flows into the freezing cylinder through the top of the tube and mix flows in through a smaller hole in the side of carburetor tube. The size of the mix inlet is balanced with the viscosity (thickness) of the liquid mix and product draw rate, in such a way that the proper amount of mix is fed into the freezer cylinder to blend with air at just the right ratio. Mix viscosity varies by mix type, mix temperature, and mix age. Different serving rates also demand different feed rates. The Crathco carburetor has an outer sleeve that can be rotated to line up with different hole sizes to provide ideal overrun under all operating conditions. You will need to experiment to determine how much mix to add to the freezing cylinder at start-up. This can be done by watching the level of mix through the clear plastic dispensing valve when filling the hopper. When the correct amount of mix feeds into the freezing cylinder install the carburetor tube in the "Off" position (outer sleeve set between any two holes) and turn the freezer "ON" to freeze down to proper consistency. Overrun Overrun is the increase in product volume, expressed as a percentage, resulting from the entrapment of air in liquid mix as it is frozen. The rotating dasher blends air into the mix as it is frozen, resulting in increased product volume. For example, if one gallon (4.4 liters) of liquid mix is poured into a freezer and one and a half gallons (6.6 liters) of frozen product is drawn out, the result is a fifty percent volumetric increase, or a fifty (50%) percent “overrun”. Why is overrun important? The introduction of air into the finished frozen product is essential from two standpoints...taste and profitability. Frozen product with a low percentage of overrun costs more to serve, appears wet, and is heavy. The introduction of air makes the finished frozen product taste richer. Too much air causes the finished product to be too light and fluffy, making it less satisfying and adversely affecting sales. The optimum percentage of overrun varies from one type of mix to another, but 50% overrun is a good average. The ingredients in some mixes take on and hold air easier than others. Overrun also affects profitability. For example, an increase from 25% to 50% overrun represents a mix savings of 17%. Uniform overruns ensures consistent portion costs. If overrun is allowed to drop, it will cost more to serve a portion of finished product. Computing Overrun 1) Weigh an empty cup. 2) Weigh this cup filled to the top with liquid mix, and subtract the weight of the cup. Note: Repeat this step only when changing mix sources, as mix weight will vary slightly from one supplier to another. Crathco® 5000 Series Manual Page 7 Computing Overrun (cont.) 3) Draw a heaping cup of f...