valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
If your loudspeakers have two sets of terminals then it is possible to bi-amp your system using a further power amplifier. Bi-amping uses two amplifiers to drive the bass and treble units in the loudspeakers independently, resulting in even greater clarity coupled with improved control and dynamics. An example of a bi-amp setup is illustrated in the diagram adjacent. Please note that if using a second azur amplifier as the slave amplifier, any line input can be used to connect from the master’s Pre-Out. Using Speaker B connections The Speaker B connections on the back of the amplifier allow a second set of speakers to be used, which could be for another room. Tape In Rec Out 1 Rec Out 2 Rec Out 2 Rec Out 1 Tape In Max Power Consumption: 615W Pre-Out Impedance 4 - 8 ohms Loudspeaker Terminals Important Please ensure that loudspeaker terminals are fully tightened Veuillez s'assurer que les bornes de l'enceinte sont entierement serrees Impedance 4 - 8 ohms Right Left Right Left Left A B B Right Left A Right AV / MD DVD Tuner / DAB CD Aux / Phono Aux / Phono CD Tuner / DAB DVD AV / MD Pre-Out Right Left Right Left Ground Manufactured in an ISO9002 approved facility Power AC Designed and Engineered in London, England Risk of electric shock Do not open Caution Risque de choc electrique Ne pas ouvrir Avis Vorm offnen des gerates Netzstecker ziehen Achtung azur 640A Integrated Amplifier Power Rating: 230V AC 50Hz Tape In Rec Out 1 Rec Out 2 Rec Out 2 Rec Out 1 Tape In Pre-Out Impedance 4 - 8 ohms Loudspeaker Terminals Important Please ensure that loudspeaker terminals are fully tightened Veuillez s'assurer que les bornes de l'enceinte sont entierement serrees Impedance 4 - 8 ohms Right Left Right Left Left A B B Right Left A Right AV / MD DVD Tuner / DAB CD Aux / Phono Aux / Phono CD Tuner / DAB DVD AV / MD Pre-Out Right Left Right Left Ground Manufactured in an ISO9002 approved facility Power AC Designed and Engineered in London, England Risk of electric shock Do not open Caution Risque de choc electrique Ne pas ouvrir Avis Vorm offnen des gerates Netzstecker ziehen Achtung azur 640A Integrated Amplifier Power Rating: 230V AC 50Hz Max Power Consumption: 615W Master amplifier Slave amplifier - if using an integrated amplifier, volume must be set to full CD player Bass Bass Treble Treble OPERATING INSTRUCTIONS Integrated Amplifier Volume Balance Aux / Phono CD DVD AV / MDTuner / DAB Tape Mon TrebleBass Direct Protection Speaker BPhonesStandby / On azur 640A Standby/On Switches the unit between Standby mode (indicated by dim power LED) and On (indicated by bright power LED). Standby is a low power mode where the power consumption is less than 10 Watts. The unit should be left in standby when not in use. Headphone s ssocket Allows for the connection of headphones with a ." Jack plug connector. When the headphones are connected the loudspeaker relay is released switching off the output to the loudspeakers (Speakers A and B). Speaker B BB o oon/off Enables/disables the secondary set of speaker terminals on the back panel. This can be used for listening to an extra set of speakers in another room. Please note that care should be taken when selecting if two loudspeakers are going to be used on each channel. If the combined resistance measured on the speaker terminals is too low the amplifier may not switch out of standby mode until a suitable load resistance is detected. For more information please see section on CAP5 protection system. Note - W When u uusing t ttwo p ppairs o oof s sspeakers e eeach p ppair s sshould b bbe r rrated a aat least 6 66 o oohms ( ((or h hhigher). 4 44 o oohm s sspeakers a aare n nnot r rrecommended w wwhen using m mmore t tthan o oone p ppair. Direct This control gives the audio signal a more direct path to the power amplifier stage of your amplifier, bypassing the tone control circuits for the purest possible sound quality. 10 Bass a aand t ttreble t ttone c ccontrols These controls allow subtle adjustments to the tonal balance of the sound. In the central position these controls have no effect. These controls only modify the sound through your loudspeakers and the Pre- Out sockets (where featured), they do not affect the signals sent through the Tape Out connections. With a well produced CD and a good system the tone controls are unnecessary and can be switched out. If the musical recording is of poor quality and/or the loudspeakers/surroundings are lacking it may be necessary to adjust the tone controls to compensate. Volume The Volume control increases/decreases the level of the sound from the outputs of the amplifier. This control affects the level of the Loudspeaker output, the pre amp output and the headphone output. It does not affect the Tape Out Connections. It is advisable to turn the Volume control fully anti-clockwise before switching the amplifier on. Balance This control allows you to adjust the relative output levels of the l...
Questo manuale è adatto anche per i modelli :Home theater - AZUR 540A (12.15 mb)