valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
By using this system’s USB hub ports, you can operate USB components from a computer through this system. You can connect an optional USB component with a maximum current consumption of 100 mA or less to each port. For details on compatible USB components, refer to the operating instructions “USB Hub Port Information” provided with this system. 1 Connect the system to a computer with the supplied USB cable (see “Connecting a personal computer to the system” on page 22). When the system power is turned on, the USB indicator lights up. USB indicator 2 Connect an optional USB component to this system’s USB hub port. If the USB indicator turns off The connected USB component has a maximum current consumption in excess of 100 mA, so it cannot be used with this system. The USB STATUS lamp on the unit lights up. In this case, follow the procedures below. 1 Disconnect the optional USB component from this system. 2 When instructions are displayed on the PC monitor, please follow them. If any instructions are not displayed on the PC monitor, disconnect the USB cable from personal computer and reconnect it. If the USB STATUS lamp on the unit does not turn off after performing the above measures, restart the computer. Notes • You cannot use a USB component with a maximum current consumption in excess of 100 mA. • When connecting this system’s USB hub ports to Hi-Speed USB components, the transfer rate will be slower than when connected directly to the computer. • Operation is not guaranteed for all the recommended USB components. • Operation is not guaranteed when the computer and the system are connected through a USB hub or a USB extension cable. • Do not connect a USB bus power hub port (that receives power from other components) to this system’s USB ports. • When the USB component has an AC power adaptor, be sure to connect the AC power adaptor to a power supply. Tips • This system’s USB hub is a full-speed (maximum transfer rate 12 Mbps), bus power type (type that receives power from a computer). • You can use the optional USB component even when; – The system power is turned off. – The function selection is other than PC. Optional Personal Computer (except for AWP-ZP1) 27GB Optional Components Hooking up optional components To enhance your system, you can connect optional components. Refer to the operating instructions provided with each component. AWP-ZP5 is used for illustration purpose. From the audio output jacks of an optional analog component Optional analog component A personal computer Optional USB component A MD jacks Use audio cords (not supplied) to connect an optional analog component (MD deck or VCR, etc.) to these jacks. You can then listen to the sound from the component. B USB port (except for AWP-ZP1) Use the supplied USB cable to connect a personal computer (see “Optional Personal Computer (except for AWP-ZP1)” on page 22). C USB hub ports (AWP-ZP5 only) Connect an optional USB component (USB memory key, etc.) to these USB hub ports (see “Connecting an optional USB component” on page 27). 28GB Listening to audio from a connected component 1 Connect audio cords. See “Hooking up optional components” on page 28. 2 Press FUNCTION repeatedly (or MD* on the unit) until “MD” appears. Start playing the connected component. * AWP-ZP1 only Optional Components 29GB Troubleshooting Problems and remedies Should you encounter a problem with your system, do the following: 1 Make sure the power cord and speaker cords are correctly and firmly connected. 2 Find your problem in the troubleshooting checklist below and take the indicated corrective action. If the problem persists after doing all of the above, consult your nearest Aiwa dealer. When the ?/1 indicator flashes Immediately unplug the power cord and check the following items. • If your system has a voltage selector, is the voltage selector set to the correct voltage? Check the voltage for your region, then make sure the voltage selector is set correctly. • Are the + and – speaker cords shortcircuited? • Are you using the supplied speakers? • Is anything blocking the ventilation holes on the rear of the system? Check all the above items and fix any problems found. After ?/1 indicator stops flashing, reconnect the power cord and turn on the system. If the indicator still flashes, or if the cause of the problem cannot be found even after checking all the above items, consult your nearest Aiwa dealer. General The display starts flashing as soon as you plug in the power cord even though you have not turned on the system (see step 4 of “Hooking up the system” (page 7)). • Press DISPLAY twice while the system is off. The demonstration disappears. “– –:– –” appears in the display. • A power interruption has occurred. Set the clock (page 9) and timer settings (page 19) again. The clock setting/radio presetting/timer is canceled. • Redo the following: – “Setting the clock” (page 9) – “Presetting radio stations” (page 13) – “Falling asleep to music” and “Waking up t...
Questo manuale è adatto anche per i modelli :Home theater - AWP-ZP1 (457.4 kb)
Home theater - AWP-ZP3 (457.4 kb)