valutazioni - 3, GPA: 3.3
(
)
)
|
Facilità d'uso
(not supplied), which has a digital coaxial output jack: © • VCR, digital satellite receiver, PlayStation, or portable audio source, etc. (not supplied): @ of the VCR or digital satellite receiver, etc. digital satellite receiver, PlayStation, or portable audio source, etc. 23GB Getting Started Getting Started Connecting the antenna (aerial) To connect the antenna (aerial) Note • Be sure to fully extend the FM wire antenna (aerial). • After connecting the FM wire antenna (aerial), keep it as horizontal as possible. HP • If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM antenna (aerial) as shown below. Outdoor FM antenna (aerial) Unit -M COAXIAL 750 ANTENNA 24GB Inserting the wireless transceiver You can transmit sound from the unit to an S-AIR product, such as the surround amplifier or S-AIR receiver. To transmit sound from the unit, you need to insert the wireless transceivers into the unit and S-AIR product. For details of S-AIR products, see “Using an S-AIR Product” (page 44). Rear panel of the unit Rear panel of the surround amplifier Wireless transceiver Wireless transceiver 25GB Getting Started Getting Started Connecting to the network Wired Setup Use a LAN cable to connect to the LAN (100) terminal on the unit. Broadband ADSL modem/ Internet router cable modem USB Wireless Setup Use a wireless LAN via the USB Wireless LAN Adapter (Sony UWA-BR100* only) (not supplied). The USB Wireless LAN Adapter may not be available in some regions/countries. * As of January 2010. Turn the unit off before connecting the extension cable or inserting the USB Wireless LAN Adapter. After inserting the USB Wireless LAN Adapter to the base of the extension cable and connecting the extension cable to the •<* (USB) port (front or rear), turn the unit on again. cable modem router Wireless LAN Adapter and the wireless LAN router closer to each other. To set the network settings For details, see [Network Settings] (page 60) and follow the on-screen instructions to complete the setup. About wireless LAN security Since communication via the wireless LAN function is established by radio waves, the wireless signal may be susceptible to interception. To protect wireless communication, this system supports various security functions. Be sure to correctly configure the security settings in accordance with your network environment. No Security Although you can easily make settings, anyone can intercept wireless communication or intrude into your wireless network, even without any sophisticated tools. Keep in mind that there is a risk of unauthorized access or interception of data. WEP WEP applies security to communications to prevent outsiders from intercepting communications or intruding into your wireless network. WEP is a legacy security technology that enables older devices, which do not support TKIP/AES, to be connected. WPA-PSK (TKIP), WPA2-PSK (TKIP) TKIP is a security technology developed to correct for the deficiencies of WEP. TKIP assures a higher security level than WEP. WPA-PSK (AES), WPA2-PSK (AES) AES is a security technology that uses an advanced security method that is distinct from WEP and TKIP. AES assures a higher security level than WEP or TKIP. Note • The placement distance between the USB Wireless LAN Adapter and your wireless LAN router differs depending on the usage environment. If the system cannot connect to the network or the network connection is unstable, move the USB Wireless LAN Adapter to a different position or place the USB 26fiB Step 3: Setting up the S-AIR Wireless System Before performing Step 3 Make sure all connections are secure, and then connect the AC power cords (mains leads). To use the S-AIR wireless system, you need to set up the surround amplifier. The unit transmits sound to the surround amplifier that is connected to the surround speakers. To activate wireless transmission, perform the following Steps. 1 Press 1/1 to turn the system on. 1/1 Make sure that “S-AIR” light up in the front panel display. When “S-AIR” does not light up, make sure that the wireless transceiver is inserted into the unit correctly. 2 Set the SURROUND SELECTOR switch of the surround amplifier to SURROUND. 4 Press 1/1 to turn the surround amplifier on. When wireless transmission is activated, the S-AIR/STANDBY indicator turns green. S-AIR/STANDBY indicator If the S-AIR/STANDBY indicator does not turn green, see “Surround amplifier” (page 11). For details of the S-AIR function, see “Using an S-AIR Product” (page 44). About the standby mode The surround amplifier enters standby mode automatically (the S-AIR/STANDBY indicator turns red) when the main unit is in standby mode or wireless transmission is deactivated. The surround amplifier is turned on automatically (the S-AIR/STANDBY indicator turns green) when the system is turned on and wireless transmission is activated. 3 Set the S...
Questo manuale è adatto anche per i modelli :Home theater - BDV-E970W (2.24 mb)