valutazioni - 3, GPA: 3.7
(
)
)
|
Facilità d'uso
• To output an audio signal from the HDMI (OUT) jack, you need to change the audio output setting. For details, see [Audio Output] in [Audio Settings] (page 60). When the component does not have an HDMI OUT jack Video signals from the system and the components are sent to the TV, and audio signals from the components are sent to the system as follows. TV System Signal flow : Audio signal : Video signal 21GB Getting Started Getting Started Getting Started • VCR or digital satellite receiver, etc. (not supplied), which has a digital optical output jack (for Russian models) or digital coaxial output jack (for other models): D • VCR, digital satellite receiver, PlayStation, or portable audio source, etc. (not supplied): E Russian models Rear panel of the unit To the audio out jacks of the VCR, digital satellite receiver, PlayStation, or portable audio source, etc. AUDIO AUDIO IN L R DIGITAL IN SAT/CABLE OPT TV OPT To the digital optical out jack of the VCR or digital satellite receiver, etc. E Audio cord (not supplied) D Digital optical cord (not supplied) Other models Rear panel of the unit To the audio out jacks of the VCR, digital satellite receiver, PlayStation, or portable audio source, etc. DIGITAL IN SAT/CABLE COAX OPT TV AUDIO AUDIO IN L R To the digital coaxial out jack of the VCR or digital satellite receiver, etc. E Audio cord (not supplied) D Digital coaxial cord (not supplied) 22GB Connecting the antenna (aerial) or Rear panel of the unit Connecting the antenna (aerial) or Rear panel of the unit FM wire antenna (aerial) (supplied) Note • Be sure to fully extend the FM wire antenna (aerial). • After connecting the FM wire antenna (aerial), keep it as horizontal as possible. Tip • If you have poor FM reception, use a 75-ohm coaxial cable (not supplied) to connect the unit to an outdoor FM antenna (aerial) as shown below. Unit Outdoor FM antenna (aerial) ANTENNA FM 75 COAXIAL Getting Started 23GB Getting Started Getting Started You can transmit the audio signal from the main unit to an S-AIR product, such as the surround amplifier or S-AIR receiver. To transmit sound from the unit, insert one wireless transceiver into the main unit and the other one into the S-AIR product, e.g. the surround amplifier. For details of S-AIR products, see “Using an S-AIR Product” (page 45). Rear panel of the unit Rear panel of the surround amplifier Wireless transceiver EZW-RT10 Wireless transceiver Note • Please make sure to fully insert the wireless transceiver into the wireless transceiver slot. You should hear a click when the wireless transceiver is inserted correctly. • To avoid inserting the wireless transceiver upside-down, orient it with the Sony logo facing up. 24GB Step 3: Connecting to the Network Step 3: Connecting to the Network Wired Setup Use a LAN cable to connect to the LAN (100) terminal on the unit. LAN cable (not supplied) Broadband ADSL modem/ router cable modem Tip • Using a shielded LAN cable, straight or crossing, is recommended. To set the network settings Select [Network Settings], [Internet Settings], then [Wired Setup] (page 64), and follow the on- screen instructions to complete the setup. Internet USB Wireless Setup Use a wireless LAN via the USB Wireless LAN Adapter (Sony UWA-BR100* only) (not supplied). The USB Wireless LAN Adapter may not be available in some regions/countries. * As of January 2010. Turn the unit off before connecting the extension cable or inserting the USB Wireless LAN Adapter. After inserting the USB Wireless LAN Adapter to the base of the extension cable and connecting the extension cable to the (USB) port (front or rear), turn the unit on again. Wireless LAN ADSL modem/ Internet router cable modem Note • The placement distance between the USB Wireless LAN Adapter and your wireless LAN router differs depending on the usage environment. If the system cannot connect to the network or the network connection is unstable, move the USB Wireless LAN Adapter to a different position or place the USB Wireless LAN Adapter and the wireless LAN router closer to each other. To set the network settings Select [Network Settings], [Internet Settings], then [USB Wireless Setup] (page 64), and follow the on-screen instructions to complete the setup. Tip • For details on wireless network setup, please visit the following URL. For customers in Russia For customers in Asia and Australia About wireless LAN security Since communication via the wireless LAN function is established by radio waves, the wireless signal may be susceptible to interception. To protect wireless communication, this system supports various security functions. Be sure to correctly configure the security settings in accordance with your network environment. USB Wireless LAN Adapter LAN cable (not supplied) Getting Started 25GB Getting Started Getting Started Although you can easily make settings, anyone can intercept wireless communication or intrude into...