valutazioni - 3, GPA: 4
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Home theater - HT-DDW860 (82.04 kb)
Home theater - HT-DDW860 (4.48 mb)
Facilità d'uso
18GB 6: Setting up the sub woofer Listening to the sub woofer POWER indicator POWER Before playing the program source, set the volume to minimum on the receiver. 1 Turn on the receiver. 2 Press input buttons (e.g., DVD) to select the program source (e.g., DVD player). 3 Press POWER on the sub woofer. The POWER indicator on the sub woofer lights up. 4 Play the program source. Adjusting the level Slight adjustments to the system can enhance your sound enjoyment. LEVEL Turn LEVEL to adjust the volume. Set the volume level to best suit your preference according to the program source. Note Do not set the volume of the sub woofer to maximum. Extraneous noise may be heard. 7: Adjusting the speaker levels and balance — TEST TONE Adjust the speaker levels and balance while listening to the test tone from your listening position. Use the remote for the operation. Tip The receiver employs a test tone with a frequency centered at 800 Hz. 1 Press ?/1 to turn on the receiver. 2 Press TEST TONE. “T. TONE” appears in the display and the test tone is output from each speaker in sequence. Front (left) t Center t Front (right) t Surround (right) t Surround back t Surround (left) t Sub woofer 3 Adjust the speaker levels and balance using the LEVEL menu so that the level of the test tone sounds the same from each speaker. For details on the LEVEL menu settings, see page 32. Tips • To adjust the level of all speakers at the same time, press MASTER VOL +/– on the remote or turn MASTER VOLUME –/+ on the receiver. • The adjusted value are shown in the display during adjustment. 4 Press TEST TONE again after adjustment. The test tone turns off. Notes • The test tone cannot be used when MULTI CH IN function is used. • Although these adjustments can also be made via the front panel using the LEVEL menu (when the test tone is output, the receiver switches to the LEVEL menu automatically), we recommend you follow the procedure described above and adjust the speaker levels from your listening position using the remote. Getting Started 19GB Amplifier Operation Selecting the component 1 Press input buttons to select the input. To select the Press VCR VIDEO 1 or VIDEO 2 Satellite tuner VIDEO 2 DVD player DVD MD or tape deck MD/TAPE Super Audio CD or SA-CD/CD CD player Built-in tuner (FM/AM) TUNER FM/AM The selected input appears in the display. 2 Turn on the component and start playback. Note If you select the VCR or DVD player, set the TV’s video input to match the component you selected. 3 Turn MASTER VOLUME –/+ to adjust the volume. Note To avoid damaging your speakers, make sure that you turn down the volume before you turn off the receiver. To mute the sound Press MUTING on the remote. The muting function will be canceled when you do the following. • Press MUTING on the remote again. • Turn the power off. • Increase the volume. To use the headphones Connect the headphones to the PHONES jack. • When the headphones are connected, speaker output is automatically canceled and “SP A” and “SP B” do not light up in the display. • When the headphones are connected, you can select only the following sound fields (page 29). – HP 2CH (HEADPHONE 2CH) – HP MULTI (HEADPHONE MULTI) – HP THEA (HEADPHONE THEATER) 20GB Listening to multi channel sound — MULTI CH IN You can select the audio directly from the components connected to the MULTI CH IN jacks. This enables you to enjoy high quality analog inputs such as DVD or Super Audio CD. When MULTI CH IN is selected, the tone and sound field cannot be used. Press MULTI CH IN. Press again to cancel the MULTI CH IN function. Note To optimize the sound balance of this system, we recommend that you set the speaker configuration of your DVD or Super Audio CD player as follows: Speaker type Settings FRONT SMALL CENTER SMALL SURROUND/REAR SMALL SUB WOOFER YES When MULTI CHANNEL DECODING indicator lights up The MULTI CHANNEL DECODING indicator lights up when the receiver is decoding multi channel sources. However, this indicator does not light up if you select 2CH STEREO mode. Listening to FM/AM radio You can listen to FM and AM broadcasts through the built-in tuner. Before operation, make sure you have connected the FM and AM antennas to the receiver (see page 13). Tip The tuning scale differs depending on the area code as shown in the following table. For details on area codes, see page 2. Area code FM AM CEL, CEK, AU 50 kHz 9 kHz Automatic tuning If you do not know the frequency of the station you want, you can let the receiver scan all available stations in your area. 1 Press TUNER FM/AM repeatedly to select the FM or AM band. The last received station is tuned in. 2 Press TUNING + or TUNING –. Press TUNING + to scan from low to high; press TUNING – to scan from high to low. The receiver stops scanning whenever a station is received. Tip If “STEREO” flashes in the display and the FM stereo reception is poor, press FM MODE to change to monaural (MONO). You will not be able to enjoy the stereo effect, but the s...