valutazioni - 6, GPA: 4.5
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
The cooling fan is activated automatically to supply cool air to the unit. Please observe the following cautions for your safety. • Make sure the unit is well-ventilated. If the unit has poor ventilation, the temperature inside the unit could rise and may damage it. • Do not obstruct the cooling fan or ventilation holes. (If the cooling fan or ventilation holes are covered with a newspaper or cloth, heat may build up inside the unit and fire may result.) Cooling Fan SUBWOOFER REAR R FRONT R CENTER REAR L FRONT L IMPEDANCE FRONT / CENTER / REAR : 6. SUBWOOFER : 3. Connecting the FM and AM Antennas FM antenna connection AM antenna connection 1. Connect the FM antenna supplied to the FM 75. COAXIAL terminal as a temporary measure. 2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or other rigid surface. • If reception is poor, connect an outdoor antenna. Before attaching a 75. coaxial cable (with a standard type connector), disconnect the supplied FM antenna. 1. Connect the AM loop antenna supplied to the AM and terminals. 2. If reception is poor, connect an outdoor single vinyl-covered wire to the AM terminal. (Keep the AM loop antenna connected). Snap the tabs on the loop into the slots of the base to assemble the AM loop antenna. FM Antenna (supplied) AM Loop Antenna (supplied) If AM reception is poor, connect an outdoor AM antenna(not supplied). Connecting the Video to TV CONNECTIONS Composite Video (Good Quality) Connect the supplied video cable from the VIDEO OUT jack on the back panel of the system to the VIDEO IN jack on your television. Scart (Best Quality) If you television is equipped with an SCART input, connect an Scart Jack (not supplied) from the AV OUT jack on the back panel of the system to the SCART IN jack on your television. For using the SCART cable • If Scart is equipped for your TV, set RGB-COMPOSITE selector of the center unit to RGB. You can get a better picture quality by using Scart setting. • If Scart (RGB Input) is not equipped for your TV, set RGB- COMPOSITE selector to COMPOSITE. COMPOSITE RGB COMPOSITE RGB • On the rear panel SCART cable is indicated as “AV OUT.” Connecting an External Digital Component Example: Digital signal components such as a Set-Top Box or CD Recorder. Optical Cable (not included) Press AUX on the remote control to select ‘DIGITAL IN’. • Each time the button is pressed, the selection changes as follows: DIGITAL IN Connecting to an External Analog Component Example: Analog signal components such as a VCR, and TV. Audio Cable If the external analogcomponent has onlyone Audio Out, connect either left or right. R L AUDIO OUT 1 Connect Audio In on the DVD player to Audio Out on the external analog component. • Be sure to match connector colors. 2 Press AUX on the remote control to select AUX. • Each time the button is pressed, the selection changes as follows: DIGITAL IN . AUX. • You can also use the FUNCTION button on the main unit. The mode switches as follows: DVD/CD . DIGITAL IN . AUX . FM . AM. CONNECTIONS Disc Playback 1 1 Press OPEN/CLOSE button to open the disc tray. 3 Press OPEN/CLOSE button to close the disc tray. • Playback starts automatically. To stop playback, press STOP during playback. • If pressed once, “PRESS PLAY” is displayed and the stop position will be stored in memory. If PLAY/PAUSE ( ) button or ENTER button is pressed, playback resumes from the stop position. (This function works only with DVDs.) • If pressed twice, “STOP” is displayed, and if PLAY/PAUSE ( ) button is pressed, playback starts from the beginning. Selecting the Video Format Turn off the main unit and then press NTSC/PAL. • By default, the video format is set to "PAL". • Each time the button is held down 5 seconds, the video format switches between "NTSC" and "PAL". • Each country has a different video format standard. • For normal playback, the video format of the disc must be the same as the video format of your TV. 2 Load a disc. • Place a disc gently into the tray with the disc’s label facing up. • Depending on the content of the disc, the initial screen may appear different. To temporarily pause playback, press PLAY/PAUSE during playback. • To resume playback, press PLAY/PAUSE button again. 18 OPERATION • Depending on the recording mode, some MP3-CDs cannot be played. • Table of contents of a MP3-CD varies depending on the MP3 track format recorded on the disc. Note MP3-CD Playback Data CDs (CD-ROMs, CD-Rs, CD-RWs) encoded in MP3 format can be played. 2 In Stop mode, use to select the album, and then press the ENTER button. • The MP3 menu screen will appear and playback will start. • Depending on the MP3 disc, the appearance of the menu may be different. 1 Press the OPEN/CLOSE button to open the disc tray, and then load the MP3 disc. MP3 4 Press the STOP button to stop playback. • To select another album and track, repeat Steps 2 and 3 above. 3 To change the album, use to select another album in Stop mo...
Questo manuale è adatto anche per i modelli :Home theater - HT-DS100 (8.78 mb)