valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
• To ensure the longest battery life and best battery performance, always charge the battery when the air temperature is between 18–24°C. Do not charge the battery pack when the temperature is below 0°C, or above 40°C. This is important. Failure to observe this safety rule could cause serious damage to the battery pack. • Do not incinerate the battery pack even if it is seriously damaged or can no longer hold a charge. The battery pack can explode in a fire. • Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks open or cracks, immediately discontinue its use and do not recharge it. • The battery pack utilizes nickel-cadmium cells. Cadmium is considered to be a toxic material. Use an environmentally safe disposal unit at a municipal waste disposal centre to dispose of a damaged or worn out battery. Unpacking Due to modern mass production techniques, it is unlikely that your GMC Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury. Know your product This drill is mainly used for drilling in wood or metal sheet and screwdriving. Use the tool and accessories only for intended applications. All other applications are expressly ruled out. 1. Keyless chuck 2. Torque collar 3. Trigger with variable speed control 4. Forward/reverse switch 5. Side handle 6. Side handle clamp knob 7. Battery pack release tabs 8. Rechargeable battery pack 9. Charger 10. LED Lights 11. Battery indicator button 12. LED Light switch 6 5 1 2 4 3 10 11 12 9 7 8 Fitting and removing the battery pack To remove the battery pack from the drill firmly press the battery release tabs (7) at either side of the battery pack, and slide the battery backward out of the tool. To install the battery pack, align rails, on the tool with the tabs on the battery pack and slide the battery pack on to the drill. Ensure the battery pack is sitting straight on the foot and correctly entering the runners. The battery should slide fully on to the drill foot until the battery pack “clicks” into position. Battery charging 1. Connect charger (9) to power source. The green light (a), should light up. This indicates the charger is ready to begin charging. 2. Position battery pack on charger, align rails (d), on battery charger with (e) on battery pack. Slide battery forward onto charger until it clicks into position. 3. The red light (b), should begin to glow continuously, indicating that the battery pack is receiving a “Fast Charge”. 4. After approximately one hour, the “Fast Charge” indicator red light (b) should go out indicating that the battery pack is fully charged and that the charger is now in a “Maintenance Charge” mode, this is confirmed by the light (a) coming back on. The battery pack can be left on Maintenance Charge” until you are ready to use it. 5. To remove the battery pack from the charger depress the battery pack release buttons (6) and slide the battery off. Warning. Do not leave batteries charging for longer than 24 hours. Note. Depending on room temperature, line voltage, and existing charge level, initial battery charging may take longer than one hour. Note. Disconnect charger from power source when not in use. To obtain the best life for the battery Never allow the drill to come to a complete stand still before recharging. The battery should be placed on charge whenever the battery is noticeably running down or the drill no longer performs a task it previously performed. Avoid conducting short charges. Make sure that the battery is fully charged every time by allowing the charger to complete its full charging cycle. Avoid allowing lose items like screws or nails etc to be stored with battery packs as these or similar items can short battery packs and cause a fire or explosion. b a d e Always unplug the charger when not in use and store in a dry secure place. Avoid charging or storing your battery in temperatures below 0.C and above 40.C. Battery indicator To activate the battery indicator feature first pull the trigger switch (3) then press the battery indicator button (11), this will display the level of charge remaining in the battery. There are 3 levels of charge low, medium and high. When the battery indicator is showing only 1 LED (low) the battery should be removed and put on the charger. LED Work area light The drill has 3 LED lights (10) to illuminate the work area and improve vision when drilling in areas with insufficient light. To turn the LED lights on and off depress the LED light switch (12). Using the drill Use the forward/reverse switch (4) to select the direction of rotation, then pull the trigger (3). This trigger switch is an electronic variable speed control which enables the user to vary the speed continuously. The speed varies according to how far the trigger switch is depressed, the further it is depre...
Questo manuale è adatto anche per i modelli :Trapani e shuropopverty - GTX24250 (461.17 kb)