valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
Selecting Speed The speed selector is on top of the motor housing. Allow the tool to come to a complete stop before changing speeds. See “Applications” for recommended speeds under various conditions. 1. For Low speed (up to 450 RPM), push the speed selector to display “1”. 2. For High speed (up to 1800 RPM), push the speed selector to display “2”. 1 2 4 8 6 7 5 3 Fig. 1 Hooks Slots WARNING Recharge only with the charger specifi ed for the battery. For specifi c charging instructions, read the operator’s manual supplied with your charger and battery. This tool is not compatible with V™-technology or NiCd systems. WARNING Always lock trigger or remove battery pack before changing or removing accessories. Only use accessories specifi cally recommended for this tool. Others may be hazardous. WARNING To reduce the risk of injury, wear safety goggles or glasses with side shields. WARNING Always lock trigger or remove battery pack before changing or removing accessories. Only use accessories specifi cally recommended for this tool. Others may be hazardous. WARNING To reduce the risk of injury, always use a side handle when using this tool. Always brace or hold securely. Ensure side handle is tightened securely before each use. Wood 6 7 Fig. 4 To Drive Screws The torque specifi cations shown here are approximate values. NOTE: Because the above settings are only a guide, use a piece of scrap material to test the different clutch positions before driving screws into the workpiece. Torque selector collar setting Torque 1 - 5 0 - 16 in. lbs. 6 - 10 17 - 27 in. lbs. 11 - 15 28-37 in. lbs. 16 - 20 38-46 in. lbs. 21-24 47-60 in. lbs. Drill 1 Low 2 High 650 in. lbs. 250 in. lbs. Fig. 3 To Drill Fig. 2 To Hammer Fig. 5 Using Control Switch The control switch may be set to three positions: forward, reverse and lock. Due to a lockout mechanism, the control switch can only be adjusted when the ON/OFF switch is not pressed. Always allow the motor to come to a complete stop before using the control switch. For forward (clockwise) rotation, push in the control switch from the right side of the tool. Check the direction of rotation before use. Starting, Stopping and Controlling Speed 1. To start the tool, grasp the handle fi rmly and pull the trigger. NOTE: An LED is turned on when the trigger is pulled. 2. To vary the speed, increase or decrease the pressure on the trigger. The further the trigger is pulled, the greater the speed. 3. To stop the tool, release the trigger. Make sure the bit comes to a complete stop before laying the tool down. Drilling Place the bit on the work surface and apply firm pressure before starting. Too much pressure will slow the bit and reduce drilling effi ciency. Too little pressure will cause the bit to slide over the work area and dull the point of the bit. If the tool begins to stall, reduce pressure slightly to allow the bit to regain speed. If the bit binds, reverse the motor to free the bit from the workpiece. Push for Forward Push for Reverse PUSH TO CENTER TO LOCK Selecting Hammer, Drill or Drive Action MILWAUKEE Hammer-Drills have three operating modes: drilling with hammering action, drilling only, and driving screws. MILWAUKEE Driver Drills have two operating modes: drilling only and driving screws. To set the operating mode, rotate the application selector collar and torque selector collar to the desired symbols. 1. To use the hammer-drilling mode (Cat. No. 2611-20 only), rotate the application selector collar until the hammer symbol appears in line with the arrow. Apply pressure to the bit to engage the hammering mechanism. NOTE: The number selected on the torque collar has no effect on operation of the drill in hammer mode. NOTE: When using carbide bits, do not use water to settle dust. Do not attempt to drill through steel reinforcing rods. This will damage the carbide bits. 2. To use the drilling only mode, rotate the application selector collar until the drill symbol appears in line with the arrow. NOTE: The number selected on the torque collar has no effect on operation of the drill in drilling mode. 3. To use the driving screws mode rotate the application selector collar until the drive symbol appears in line with the arrow. Then rotate the torque selector collar until the desired clutch setting appears in line with the arrow. The adjustable clutch, when properly adjusted, will slip at a preset torque to prevent driving the screw too deep into different materials and to prevent damage to the screw or tool. For reverse (counterclockwise) rotation, push in the control switch from the left side of the tool. Check direction of rotation before use. To lock the trigger, push the control switch to the center position. The trigger will not work while the control switch is in the center locked position. Always lock the trigger or remove the battery pack before performing maintenance, changing accessories, storing the tool and any time the tool is not in use. Drilling in Wood, Composition M...
Questo manuale è adatto anche per i modelli :Trapani e shuropopverty - 2611-20 (5.57 mb)