valutazioni - 4, GPA: 3.5
(
)
)
|
Facilità d'uso
SAVE THESE INSTRUCTIONS Work Area Do not abuse the cord. Never use the cord to carry the tools or pull the plug Keep your work area clean and well lit. from an outlet. Keep cord away from Cluttered benches and dark areas invite heat, oil, sharp edges or moving parts. accidents. Replace damaged cords immediately. Do not operate power tools in explosive Damaged cords increase the risk of electric atmospheres, such as in the presence of shock. flammable liquids, gases, or dust. Power When operating a power tool outside, use tools create sparks which may ignite the an outdoor extension cord marked "W-A" dust or fumes. or "W." These cords are rated for outdoor Keep by-standers, children, and visitors use and reduce the risk of electric shock. away while operating a power tool. Refer to “Recommended sizes of Extension Distractions can cause you to lose control. Cords” in the Accessory section of this manual. Electrical Safety Personal Safety Grounded tools must be plugged into an outlet properly installed and grounded in Stay alert, watch what you are doing and accordance with all codes and use common sense when operating a ordinances. Never remove the grounding power tool. Do not use tool while tired or prong or modify the plug in any way. Do under the influence of drugs, alcohol, or not use any adaptor plugs. Check with a medication. A moment of inattention while qualified electrician if you are in doubt as operating power tools may result in serious to whether the outlet is properly personal injury. grounded. If the tools should electrically Dress properly. Do not wear loose malfunction or break down, grounding clothing or jewelry. Contain long hair. provides a low resistance path to carry Keep your hair, clothing, and gloves away electricity away from the user. Improper from moving parts. Loose clothes, jewelry, grounding can shock, burn or electrocute. or long hair can be caught in moving parts. Grounded tools are equipped with three Keep handles dry, clean and free from oil conductor cord and three prong type plugs. and grease. Before plugging in the tool be certain the Avoid accidental starting. Be sure switch outlet voltage supplied is within the voltage is “OFF” before plugging in. Carrying tools marked on the nameplate. Do not use “AC with your finger on the switch or plugging in only” rated tools with a DC power supply. tools that have the switch “ON” invites Avoid body contact with grounded accidents. surfaces such as pipes, radiators, ranges Remove adjusting keys or wrenches and refrigerators. There is an increased before turning the tool “ON”. A wrench or risk of electric shock if your body is a key that is left attached to a rotating part of grounded. If operating the power tool in the tool may result in personal injury. damp locations is unavoidable, a Ground Fault Circuit Interrupter must be used to Do not overreach. Keep proper footing supply the power to your tool. Electrician’s and balance at all times. Proper footing rubber gloves and footwear will further and balance enables better control of the enhance your personal safety. tool in unexpected situations. Don't expose power tools to rain or wet Use safety equipment. Always wear eye conditions. Water entering a power tool will protection. Dust mask, non-skid safety increase the risk of electric shock. shoes, hard hat, or hearing protection must be used for appropriate conditions. -2 Tool Use and Care other condition that may affect the tools Use clamps or other practical way to operation. If damaged, have the tool secure and support the workpiece to a serviced before using. Many accidents are stable platform. Holding the work by hand caused by poorly maintained tools. Develop or against your body is unstable and may a periodic maintenance schedule for your lead to loss of control. tool. Do not force tool. Use the correct tool for Use only accessories that are your application. The correct tool will do recommended by the manufacturer for the job better and safer at the rate for which your model. Accessories that may be it is designed.Do not use tool if switch suitable for one tool, may become does not turn it “ON” or “OFF”. Any tool hazardous when used on another tool. that cannot be controlled with the switch is dangerous and must be repaired. Service Tool service must be performed only by Disconnect the plug from the power qualified repair personnel. Service or source before making any adjustments, maintenance performed by unqualified changing accessories, or storing the tool. personnel could result in a risk of injury. For Such preventive safety measures reduce the example: internal wires may be misplaced or risk of starting the tool accidentally. pinched, safety guard return springs may be Store idle tools out of reach of children improperly mounted. and other untrained persons. Tools are When servicing a tool, use only identical dangerous in the hands of untrained users. replacement parts. Follow instructions in Maintain tools with care....