valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
Make sure the bit is properly attached before use. Attaching or removing battery pack 1. To connect the battery pack: Insert the battery pack. It snaps into place to indicate proper connection. 2. To remove the battery pack: Press the two buttons on the sides of the battery pack. Slide the battery pack out of the tool body. Select the impact mode This unit is equipped with impact mode selector switch. By sliding the mode selector switch, soft impact mode or hard impact mode can be selected. Soft impact mode has lower torque setting and help avoiding the damage of material caused by over-tightening power. It is recommended to select this mode to minimize the damage of small size screw head or the damage of the soft material surface to be fastened by controlling the trigger switch. Hard impact mode has maximum torque and rotation speed setting. When you set the impact mode, make sure to slide the mode selector switch fully to the desired impact mode setting. Do not slide the switch before the rotation has completely stopped. № )h> S H V- j S : Soft impact mode H : Hard impact mode Impact mode Maximum torque Maximum R.P.M. Recommended application S: soft impact mode 80 Nm, (820kgf-cm, 711 in-lbs) 0 - 2200 RPM small size screw, soft material, thin metal stud H: hard impact mode 120 Nm, (1220kgf-cm,1060in-lbs) 0 - 2600 RPM long size screw bolts/nut -7- Switch and Forward/Reverse lever Operation Switch lock CAUTION: To prevent damage, do not operate Forward/Reverse lever until the bit comes to a complete stop. Forward Rotation Switch Operation 1. Push the lever for forward rotation. 2. Depress the trigger switch slightly to start the tool slowly. 3. The speed increases with the amount of depression of the trigger for efficient tightening of screws. The brake operates and the bit stops immediately when the trigger is released. 4. After use, set the lever to its center position (switch lock). Reverse Rotation Switch Operation 1. Push the lever for reverse rotation. Check the direction of rotation before use. 2. Depress the trigger switch slightly to start the tool slowly. 3. After use, set the lever to its center position (switch lock). CAUTION To eliminate excessive temperature increase of the tool surface, do not operate the tool continuously (using two or more battery packs consecutively.) Tool needs cool off time before switching to another pack. LED light CAUTION: The built-in LED light is designed to illuminate the small work area temporarily. Do not use it as a substitute for a regular flashlight, since it does not have enough brightness. Depress the trigger switch, then LED light turns on. When the trigger switch is released, the light turns off automatically. The light illuminates with very low current, and it does not adversely affect the performance of the driver during use or its battery capacity. -8- How to use the belt hook WARNING: •Be sure to attach the belt hook securely to the main unit with the screw firmly fastened. When the belt hook is not firmly attached to the main unit, the hook may depart and the main unit may fall. This may result in an accident or injury. • Be sure to attach the belt hook firmly and securely onto a waist belt or other belt. Pay attention to the unit not slipping off from the belt. This may result in an accident or injury. •When the main unit is held by the belt hook, avoid jumping or running with it. Doing so may cause the hook to slip and the main unit may fall. This may result in an accident or injury. •When the belt hook is not used, be sure to return it to the storing position. The belt hook may catch on something. This may result in an accident or injury. • When the unit is hooked onto the waist belt by the belt hook, do not attach driver bits to the unit. A sharp edge object, such as a drill bit, may cause injury or an accident. To set the belt hook angle position 1. Slide the belt hook lock lever © and hold it to unlock the belt hook storing position 2. Pull the belt hook from storing position (2) and set it as desired angle 3. Release the belt hook lock lever to lock the angle of belt hook. 4. Make sure the belt hook is firmly locked. To return the belt hook to the storing position, Follow step 1. and 2. above, then lower the belt hook. To secure the lock, follow 3 and 4 above. To change the belt hook location side The belt hook can be attached to either side of the unit. 1. Set the belt hook at storing position. 2. Loosen the screw turning it counter-clock-wise, using a coin or a flat blade screw driver 3. Take out the belt hook and insert into the other side of the slot on the main unit 4. Fasten the screw firmly, turning it clockwise The belt hook can be taken out from the main unit only when it is at storing position. -9- For Appropriate use of Battery pack Ni-MH Battery pack (EY9201) • Charge the Ni-MH battery fully before storage in order to ensure a longer service life. • The ambient...