valutazioni - 1, GPA: 4
(
)
)
|
Facilità d'uso
2. Attach a standard quick connector (not included) to your 3/8” air pressure source hose. Then attach the air hose to the Air Impact Wrench. NOTE: If you are not using an automatic in-line oiler, add a few drops of pneumatic oil to the Air Inlet (36) before attaching the air hose. Add a few more drops of oil after every hour of continual use. 3. Set the air pressure regulator on your air compressor at 90 psi. WARNING: Do not exceed the recommended pressure of 90 psi. Damage to your tool, and possible personal injury and/or property damage may result. 4. Check the air line and its connections for air leaks. Make note of these, and repair them before using this tool. NOTE: Turn off your air compressor and disconnect the air pressure hose before changing sockets or making any adjustments to this tool. Severe injury or property damage may otherwise result. WARNING: This tool generates considerable torque when in use. Always hold the tool with both hands when using, and brace yourself to resist the torque which will be delivered to the work piece. 5. Select the appropriate size 3/8” square drive impact socket (not included) for your needs. Push and snap the socket onto the Anvil (9). 6. Set the direction of the Air Impact Wrench to “FORWARD” or “REVERSE”. Please see photo. By moving the Throttle Lever “Butterfly” (5) to the right, you are setting the tool to operate FORWARD. You may control the amount of torque to be applied by rotating the Regulator (38) (See photo next page). There are REVERSE FORWARD settings from 1 through 8, indicating Throttle Lever “Butterfly” (5) increasing torque. Rock the Throttle Lever “Butterfly” (5) to the left to REVERSE the direction of the tool. NOTE: In this booklet, “FORWARD” refers to clockwise rotation, and “REVERSE” refers to counterclockwise rotation of the Anvil (9). Always be aware of the direction of the threading of the fastener you are working on. While most fasteners install with clockwise rotation, some threads are intentionally the reverse. SKU 37730 Page 5 NOTE: The actual torque delivered at each of the eight settings will depend on the air pressure supplied to the tool. We suggest that you test the actual torque by tightening a nut or bolt at each setting, then observing the resultant torque by using a mechanical torque wrench (not supplied). NOTE: The actual torque delivered at each of the eight settings will depend on the air pressure supplied to the tool. We suggest that you test the actual torque by tightening a nut or bolt at each setting, then observing the resultant torque by using a mechanical torque wrench (not supplied). . If installing a nut or bolt, set it as tight as possible by hand before tightening with the Air Impact Wrench. 8. Place the socket (not included) over the fastener. 9. Grip the Air Impact Wrench tightly with both hands, and rock the Throttle Lever “Butterfly” (5) to the right.The tool will operate and tighten the fastener. 10. When the fastener is tightened, release the Throttle Lever “Butterfly” (5) , and remove the tool from the fastener. 11. If possible, check the actual torque applied to the fastener with a mechanical torque wrench (not supplied). 12. If removing a fastener, grip the Air Impact Wrench tightly with both hands, and rock the Throttle Lever “Butterfly” (5) to the left.The tool will operate and loosen the fastener (assuming that the fastener is a standard right-hand thread). NOTE: Always check to be sure of the thread direction of any fastener before attempting to install or remove it. If the fastener is a left-hand thread, rock the Throttle Lever “Butterfly” (5) to the right for removal. WARNING: If the fastener will not come off, first check to be sure of the direction of the thread. If you have the thread direction correct and the fastener will not come off, DO NOT INCREASE THE AIR PRESSURE to the tool beyond 90 psi.This may damage the tool.You may have to use penetrating oil, heat, or a mechanical wrench to remove the fastener. 13. When you are done using this tool, turn off the air compressor, and disconnect the air hose. Put the Air Impact Wrench away in its proper storage place. Maintenance 1. Your Air Impact Wrench should be kept clean and dry. 2. When not in use, store your tool in a suitable place where it will not be exposed to water, corrosive materials, or undue banging around. 3. If you are not using an in-line oiler, you should inject a few drops of pneumatic oil into the air inlet of the tool and the Oiler Screw (3) port after every hour of continuous use. 4. If your tool loses power, or you notice air leaks, take it to a certified technician for service. 5. All repairs to this tool should be performed by a qualified service technician. Regulator (38) SKU 37730 Page 6 Parts List Parts List Description Qty. 1 Rubber Nose Guard 1 2 Motor Housing 1 3 Oiler Screw 1 4 Throttle Pin 2 5 Throttle Lever 1 6 Anvil Bushing 1 7 O-Ring 1 8 Socket Retaining Ring 1 9 Anvil 1 10 Hammer Cage 1 11 Hammer 1 12 Cam 1 13 H...