Log:
valutazioni - 5, GPA: 3.8 ( )

Istruzioni per l'uso Harbor Freight Tools, Modello 94108

Produttore : Harbor Freight Tools
File Size : 281.24 kb
File Nome : 94108.pdf
Lingua di insegnamento: en
Vai a scaricare



Facilità d'uso


Securely tighten all Cap Screws (7). Note: Use pipe thread seal or Teflon tape on all threaded connections. Oiler and Filter Connection Dirt, water, and the lack of pneumatic tool oil are major causes for tool wear. It is recommended to install an optional oiler-filter, as illustrated below for better performance. Connect the air tool, air hoses, filter, and oiler to the Compressor Air Outlet as illustrated below. The filter and oiler (not supplied) are recommended but not mandatory for operation. A few drops of pneumatic tool oil must be added through the air inlet before each use if an oiler is not used. AIR SUPPLY CONNECTION 1. Install a standard 1/2” Air Connector (not included) to the Air Inlet (51). First wrap the threaded portion of the 1/2” air connector with pipe thread seal tape before threading it into the Air Inlet (51). Tighten securely. 2. Set the sir pressure regulator at no more than 100 PSI. 3. Check the air line and its connections for air leaks, make note of these, and repair them before using this tool. WARNING: Do not exceed the recommended working pressure of 100 PSI. Damage to your tool, and possible personal injury may result. OPERATION NOTE: Turn off your air compressor and disconnect the air pressure hose before changing sockets or making any adjustments to this tool. Severe injury or property damage may result otherwise. WARNING: This tool generates considerable torque when in use. Always hold the tool with both hands when using, and brace yourself to resist the torque which will be delivered to the work piece. 1. Select the appropriate size 1” square drive socket (not included) for your needs. Push and snap the socket onto the Anvil (13). NOTE: On this tool the designation “R” refers to forward or clockwise rotation. “L” refers to reverse or counterclockwise rotation. Always be aware of the direction of the threading of the fasteners you are working on. While most fasteners install with clockwise rotation, some threads are intentionally the reverse. 2. Set the directions of the Air Impact Wrench to Forward (R=right or clockwise) or Reverse (L=left or counterclockwise) by adjusting the Rotation/Torque Knob (38). You may control the amount of torque to be applied by selecting any of the 3 torque settings (1=low, 2=medium, 3=high). NOTE: The actual torque delivered at each of the 3 torque settings will depend on the air pressure supplied to the tool. We suggest that you test the actual torque by tightening a nut or bolt at each setting, then observing the resultant torque by using a mechanical torque wrench (not supplied). 3. If installing a nut or bolt, set it as tight as possible by hand. 4. Place and push on a appropriate size impact socket onto Anvil (13) and place the Impact Socket (not included) over the fastener. 5. Grip the Air Impact Wrench tightly with both hands, and squeeze the Trigger (36). The tool will operate and tighten the fastener. Air Inlet Connector (51) Rotation / Torque Knob (38) OPERATION (continued) Caution: Never increase pressure at the air compressor regulator to achieve more torque. 7. When finished, release the Trigger (36), and lift the Impact Wrench off the nut. 8. Remove the air supply hose, then squeeze the Trigger (36) again to release any remaining air pressure in the Impact Wrench air chamber. Maintenance 1. After each use, wipe the Impact Wrench with a clean cloth to remove any dirt and grease buildup. 2. To maintain tool life, always lubricate the air line by adding a few drops of pneumatic tool oil to the air line (or Air Inlet) before each use. Or, install the automatic oiler-filter system as illustrated on page 5. 3. Before each use, drain water out of the air compressor tank and condensation from the air lines. Refer to the Air Compressor Operation Manual. 4. Store the Impact Wrench in a clean and dry location. Parts List #205 Rotation / Torque Knob #60205 1 8 Assembly Drawing NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. Lubrication Gear oil should be added in part #4, use MoS2 lubricating grease. It should be added monthly. The amount is 0.033-0.044 lb. each time. Gear oil should be added in part #44, use Spindle Oil. Add 5-10 drops every day, before operating the tool. 90 Day Warranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of ...


Scrivi la tua opinione del dispositivo



Il messaggio
Il tuo nome :
Inserire le due cifre :
capcha





categorie