valutazioni - 2, GPA: 4.5
(
)
)
|
Facilità d'uso
For machine with square drive (Fig.3&4) Use 9.5 mm square drive socket with a hole for detent pin which is available on the market. (Note: Use 6.35 mm square drive socket when using the machine with 6.35 mm square drive.) To install the socket, depress the detent pin on the square drive with your finger and push the socket onto the square drive until the detent pin is inserted into the hole in the socket. To remove the socket, depress the detent pin with a small hand tool and pull off the socket. For machine with round drive (Fig. 5) Use a bit with Form C 6.3 shank which is available on the market. The bit can be inserted directly into the round drive and held in place. To install the bit, push it firmly into the round drive. To remove the bit, grasp it with a pair of pliers and pull it out of the round drive. Sometimes, it helps to wiggle the bit with the pliers as you pull. Switch action (Fig. 6) CAUTION: Before inserting the battery cartridge into the machine, always check to see that the switch trigger actuates properly and returns to the ‘‘OFF’’ position when released. To start the machine, simply pull the trigger. Release the trigger to stop. Reversing switch action (Fig. 7) CAUTION: • Always check the direction of rotation before operation. • Use the reversing switch only after the machine comes to a complete stop. Changing the direction of rotation before the machine stops may damage the machine. This machine has a reversing switch to change the direction of rotation. Slide the reversing switch up for clockwise rotation or slide it down for counterclockwise rotation. Overload protector The overload protector automatically cuts out to break the circuit whenever heavy work is prolonged. Wait 20 – 30 seconds before resuming operation. Adjusting the fastening torque (Fig. 8) The fastening torque can be adjusted infinitely from approx. 20 kg·cm to 80 kg·cm. To adjust it, loosen the two screws and turn the adjusting ring. Then tighten the screws to secure the adjusting ring. Refer to the table below for relation between the numbers on the adjusting ring and the fastening torque to be obtained. Numbers on adjusting ring Fastening torque to be obtained 1 20 kg·cm 2 35 kg·cm 3 48 kg·cm 4 60 kg·cm 5 80 kg·cm (Example) 35 kg·cm of fastening torque can be obtained when the number 2 is aligned to the red mark. NOTE: • Always tighten the two screws to secure the adjusting ring after adjusting the fastening torque. • The fastening torque may differ depending upon the kind of screws, the type of materials to be fastened, etc. Before starting your job, always perform a test operation to verify the adequate fastening torque. Operation The proper fastening torque may differ depending upon the kind or size of screws, the type of materials to be fastened, the condition of the threads, etc. Before starting your job, always perform a test operation to verify adequate fastening torque. Hold the machine firmly with both hands whenever possible and place the socket over the bolt or nut. Then turn the machine on. As soon as the bolt or nut becomes tight, the clutch will cut in and the motor will stop automatically. Release the switch trigger. When fastening machine screws, use the proper screwdriver bit shown in Fig. 9. It is commonly available on the market. NOTE: • Always use the correct size socket for bolts and nuts. An incorrect size socket will result in inaccurate and inconsistent fastening torque and/or damage to the bolt or nut. • Hold the machine with its square drive pointed straight at the bolt or nut, or the bolt or nut will be damaged. • If the motor will not start even after you pull the trigger, release the trigger. Then pull the trigger again after turning the socket slightly with your fingers. Fastening performance The following reference table indicates the approximate fastening capacity from a single 1-hour battery charge. It may differ under some conditions. Screw size Fastening torque Fastenings M6x14 5 About 800 screws 1 About 1,000 screws MAINTENANCE CAUTION: Always be sure that the machine is switched off and the battery cartridge is removed before carrying out any work on the machine. To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out by Makita Authorized Service Center. FRANCAIS Descriptif 1 Batterie 6 Carre meneur w Rotation vers la gauche 2 Capot arriere 7 Foret a queue de forme C 6.3 e Numero 3 Temoin de recharge 8 Rond meneur r Bague de reglage 4 5 Logement pour goupille a ressort Goupille a ressort 9 0 q Ga.chette Inverseur Rotation vers la droite t y Repere rouge Vis SPECIFICATIONS Modele 6702D Capacites Taille des boulon, ecrou et vis a metaux ...................... 3 mm–6mm Tournevis carre ...................... 9,5 mm ou 6,35 mm Vitesse a vide (t/mn.) .......................................... 400 Couple de serrage ................... 20 kg.cm–80kg.cm Longueur totale ............................................ 352 mm Poids net ................
Questo manuale è adatto anche per i modelli :Trapani e shuropopverty - 6702D (488.08 kb)